background image

49

4

Practical Examples

Error Messages

When one of the following messages appears on the display 
panel, an error has occurred in the scanner. Follow the 
indicated procedure to resolve the error. 

Check Imprinter

Error Code: H001
Problem:

 No ink cartridge is installed in the imprinter.

Solution:

 Install an ink cartridge.

Cover Open

Error Code: C001
Problem:

 The scanner’s upper unit is open.

Solution:

 Close (lower) the upper unit. (See p. 38.)

Error Code: C009
Problem:

 The imprinter cover is open.

Solution:

 Close the imprinter cover.

Error Code: C010
Problem: 

The pickup roller cover is open.

Solution:

 Close the pickup roller cover. (See p. 42.)

Jam

Error Code: Pxxx
Problem:

 Paper has jammed.

Solution:

 Open the upper unit and remove the jammed 

paper. (See p. 32.)

Hint

The displayed error code indicates the location of the paper jam.
• P001, P002: The document is jammed near the feed inlet.
• P004: The document is jammed inside the scanner.
• P006, P007: The document is jammed near the eject outlet.

*

P001, P006 can be considered to be due to the document feed 
speed being too fast or the leading edge of the document not 
feeding correctly.

Call for Service

Error Code: Exxx
Problem:

 Internal scanner error.

Solution:

 Turn the power OFF, and restart the scanner. If 

this does not solve the problem, make a note of the error 
code, and contact your Canon service representative.

Skew Detected

Error Code: J018
Problem:

 A skewed document page contacted the wall of 

the transport path.

Solution:

 Remove and reposition the document page.

Summary of Contents for IMAGE FORMULA DR-7550C





































































Reviews: