background image

37

3

Main

ten

a

nce

Main unit inner upper side (Upper Unit)

Cleaning the Scanning Glass and Rollers

If scanned images contain spots or documents become dirty 
after scanning, the scanning glass or transport rollers inside 
the scanner may be dirty. Please clean periodically.

IMPORTANT

Scratches on the scanning glass may cause spots or streaks on 
scanned images, as well as feeding errors. If you find a scratch on 
the scanning glass, contact your local authorized Canon dealer or 
service representative to have the glass replaced.

1.

Turn the power switch off, and disconnect the power 
plug from the power outlet.

2.

Close the document eject tray extension if it is open.

3.

Press the Open/Close button and carefully raise the 
upper unit until it stops.

4.

Wipe any dust off the scanning glass with a cleaning 
cloth or a clean, dry cloth.

Make sure that you clean both scanning glasses, the one 
below and one above.

CAUTION

Never spray mild detergent or water directly on the scanning 
glasses. The spray could penetrate below the glass, and 
contaminate the internal light source and lenses.

Sensors

Open/Close Button

Scanning 
Glass

Summary of Contents for IMAGE FORMULA DR-7550C





































































Reviews: