Canon FaxPhone L90, Service Manual

Page: 99 / 128

Chapter 11
11-3
00B1
Cannot finish V8 procedure or detect V21 signal after ANSam signal within
35sec
00B2 Can't detect phase 2 signal after our side sending CJ signal within 30 sec
00B3 Can't detect correct V21 or JM signal after sending CM signal
00B4
Can't detect correct phase 2 signal within 25 seconds after CM/JM signal
exchange
00B5 Can't detect phase 3 signal after phase 2 within 25 seconds
00B6 Can't detect phase 4 signal within 25 seconds after CM/JM exchange
00B8 Remote side disconnect after our side sending DCS signal in V34
00BA Cannot received correct signal after our side sending DTC signal in V34
00BB Every time our side received DIS signal after sending DTC in V34
00BC Modem can't ready within 10 second after entering primary channel in V34
00BD Can't detect correct V.21 or JM signal after detected FSK frequency
00BE Remote side no document to be polled after V8 handshaking
00BF Capability no match after V8 handshaking
00C1
At phase D, transmitting units out EOP 3times consecutively, but receive no
answer from receiving unit
00C2 Remote side disconnect after sending out CM signal
00C4
After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP,
DCN
00C5 Received DCN signal after sending MPS signal
00C9 At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit
00CA After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN
00CB After sending EOP signal, the received is DCN signal
00CF Received incorrect signal after sending DTC signal for V34 polling
00D0 Received ERR signal after sending EOR_NULL
00D1 Received incorrect response after sending PPS_EOP signal in V34
00D2 Received DCN after sending PPS_EOP signal
00D3 Received DCN after sending PPS_NULL signal
00D8 Can't detect correct phase 3 signal for polling within 25 seconds
00D9 Can't detect correct phase 3 signal after detect silence after phase 2
00DA
Can't detect phase 4 signal within 30 seconds or remote side hang up
over 6 seconds
00DB Can't received any T30 signal within 15 seconds within phase 4
00DC Received T30 signal in phase 4 other than DCS, DIS or DTC
00DE Remote side no SUB capability in V34
00E0
At phase D, transmitting units out PPS_NULL 3 times consecutivery but
not answer
00E1 Received incorrect response after sending PPS_NULL signal
00E2 Can't receive any response in RR response procedure after sending PPS_NULL signal
00E4
At phase D, transmitting units out PPS_MPS 3 times consecutivery but
not answer
00E5 Received incorrect response after sending PPS_MPS signal
00E6 Can't receive any response in RR response procedure after sending PPS_MPS signal
00E7 Received DCN after sending PPS_MPS signal
00E8
At phase D, transmitting units out PPS_EOP 3 times consecutivery but
not answer
00E9 Receive PIN signal after sent last page 3 times
00EA Can't receive any response in RR response procedure after sending PPS_EOP signal
00EE
At phase D, transmitting units out EOR_NULL 3 times consecutivery but
not answer
00EF Received incorrect response after sending EOR_NULL signal
00F0 Can't receive any response procedure after sending EOR_NULL signal
00F1
At phase D, transmitting units out EOR_MPS 3 times consecutivery but
not answer
00F2 Received incorrect response after sending EOR_MPS signal
00F3 Received ERR signal after sending EOR_MPS signal
00F4 Can't receive any response in RR response procedure after sending PPS_MPS signal
00F5
At phase D, transmitting units out EOR_EOP 3 times consecutivery but
not answer
00F6 Received incorrect response after sending EOR_EOP signal
00F7
After received ERR, our side can't received response after sending
EOR_EOP signal
00FC Can't receive any response ather sending CTC signal
00FD Can't speed down to lower speed in ECM mode
00FE Memory full for transmission
00FF All redialing attempts have failed.
Error Code Description