Canon FaxPhone L90, Service Manual

Page: 98 / 128

Chapter 11
11-2
0040 Can't receive carrier within 6 sec. after sending CTR signal.
0041 Can't receive carrier within 6 sec. after sending PPR signal.
0042 Can't receive correct signal after sending RNR signal
0043 Fault occurred in the communication procedure signal
0044 Can't receive carrier /FSK signal within 6 sec. after sending MCF signal in ECM mode
0047 Can't receive correct signal after sending ERR signal
0048 Can't receive correct signal after receive PPS_PRI_Q or PRI_Q, EOR_PRI_Q
004B Can't detect correct FSK signal even through detected FSK tone within 6 sec
004C Handshake fail during re-train or between page in V.34 Rx
004E Receive DCN signal after sending DIS signal in V.34
004F Remote side disconnected after sending ANSam in V.8
0050 Can't receive any correct signal after sending CJ signal in V.8
0051 Can't receive phase 3 signal after phase 2 within 20 seconds in V.34
0053 Modem disconnect after phase 4 in V.34
0054 Remote side disconnect after phase 4 in V.8
0055 Receive incorrect signal after sending DIS signal in V.34
0056 Modem disconnect after sending CFR in V.34
0058 Can't detect image signal within 6 sec after modem enter to primary phase in V.34
005A Modem cannot detect any correct ECM frame with 3 minutes in phase C
005B Modem can't detect control channel with 12 sec in phase C
005C Detect busy tone within control channel after phase C
005D Modem cannot detect any correct ECM frame with 12 sec in phase C
005E Can't detect control channel signal after received RCP frame within 6 sec
005F Can't detect silence after sending JM signal for polling Tx function
0060 There are no any bullietin files to be polled in V34
0061 Machine cannot detect V.21 or V.8 signal with 35 seconds
0062
Modem disconnect in phase D after our side sending out flags sequence
in control channel
0063 Can't receive any flag sequence in control channel within 6 sec in phase D
0064
Can't detect any control channel signal in phase D within 60 seconds even
through energy still on the line
0065
Can't detect any control channel signal within 60 seconds after detect silence
in phase D
0066 Cannot receive signal or carrier after sending CFR in V.34
0069 Capability no match paper size after received is DCS signal
0070 Reception was manually canceled on the machine.
0071 The machine's memory is full.
0080 The recipient's machine did not respond within 35 seconds.
0081 Received DTC signal in transmission phase
0082 Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B
0083 Detected FSK signal, but Can't receive any signal within 35 sec
0084 Detect DCN signal in phase B
0085
Transmitting unit sending DCS 3 times consecutively, but each time responds
with DIS/DTC
0086
Detected responds signal other than DTC, DIS, FTT, DCN or CFR after
sending DCS signal
0087 Training attempt has failed because speed unit can't adjust to low lower speed
0088 Received DCN signal after sending out DCS signal
008B Receivers protcol of DIS is received, but it is not compatible with our machine
008C Remote side not support SUB capabillity when relay initiate
008D The recipient's machine has run out of paper.
008F Modem not ready to received V.34 data within 6 sec after received CFR signal
0090 Called side document not ready for our polling
0091
Sending out DCS+TCF signal 3 times consecutively but no signal in response
from receiver
0093 Received DCN signal after sending out DCS signal for V34
0094 Time out during transmit ECM frame or RCP command
0095 Wrong ID number when polling Rx or Relay initial
0096 SUBADDRESS/PASSWORD capability not match in polling Rx mode
009A Can't detect any signal after sending CI signal
009D Remote side hang up before V34 modem enter phase 2 state in V34 polling Rx
009E Manual Tx over 15 minutes whin in phase C by non-ECM mode
00A0 Transmission was manually canceled on the machine.
00A1 There is a document jam.
00AE Can't finished V8 procedure or detect V21 signal after CM signal within 30 sec
00AF
Modem can't enter into control channel after Tx side sending out RCP signal
for V34
Error Code Description