Canon AK1 Operation Manual Download | Manualshive

Page: 23 / 62

background image

Replace the staple cartridge of the stapler unit (Staple

N1)

Introduction

When a staple cartridge of the stapler unit inside the stacker/stapler is empty, the control panel
will display a message indicating which staple cartridge must be replaced. The procedure below
describes how to replace the staple cartridge.

Required staples

Staple N1

NOTE

You can order all required supplies from your local authorized dealer.

Replace the staple cartridge of the stapler unit

Step

Action

Illustration

1

Open the front door of the stacker/stapler.

2

Grab the green tab of the staple case and
pull the staple case out of the staple unit.

NOTE

When the stapler unit is at the
back and it is difficult to pull out
the staple case, turn the dial at
the bottom left-hand side to the
left to move the stapler unit.

3

Pull out the staple cartridge.

4

Insert the new staple cartridge (Staple
N1).

4

Replace the staple cartridge of the stapler unit (Staple N1)

Chapter 3 - Use the stacker/stapler

23

Canon Finisher-AK1/Saddle Finisher-AK2/Puncher Unit-BT1/BU1

Operation Guide Finisher-AK1, Saddle Finisher-AK2, Puncher Unit-BT1-BU1: VarioPrint (VP) 110, VP120, VP135 - Edition 2013-06

«
...
21
22
23
24
25
...
»

Summary of Contents for AK1































































Reviews:

No comments

Related manuals for AK1

Document Centre 470cx

Brand: Xerox Pages: 328

Brand: Olivetti Pages: 160

Brand: Olivetti Pages: 251

Brand: Canon Pages: 62

Brand: Stratford Labs Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands