Cannondale SuperSix EVO Neo Owner'S Manual Supplement Download Page 4

Page: 4 / 36

137377 Rev 1.

English

SuperSix EVO Neo - Owner’s Manual Supplement

IDENTIFICATION

1. X35 Rear Hub Drive Unit **

2. iWoc® ONE

(drive interface)

3a. Battery (internal)**

3b. Battery (external)**

4. Bottom Bracket Cover

5. Charger/Battery Port

6. PAS Wheel Sensor **

7. Drive Unit Cable Guard

8. Front Chain Rings

9. Rear Cassette

10. Bike Serial Number Location

Serial Number

The serial number is located on downtube.

It is a 7-character code. Use this serial

number to register your bike.

To register your bike: go to the

Product Registration section of our

website at www.cannondale.com

Record YOUR Serial Number here:

________________________________________

Actual bike appearance will differ.

Parts of Your Ebike

Identification

Summary of Contents for SuperSix EVO Neo





































Search results

Summary of Contents for SuperSix EVO Neo

Reviews:

Related manuals for SuperSix EVO Neo

Brands by name

Popular brands

Cannondale SuperSix EVO Neo, Owner'S Manual Supplement

Search results

Summary of Contents for SuperSix EVO Neo

Reviews:

Related manuals for SuperSix EVO Neo

Brands by name

Popular brands