only.
authorised technicians
by
checked regularly and replaced
be
The cable must
•
The cable must not be bent or compressed.
•
and that it is compliant with safety regulations.
made
been
The installer must ensure that the correct electrical connection has
•
contacts.
circuit-breaker must be installed with a minimum opening of 3mm between
If the appliance is being connected directly to the mains an omnipolar
•
by after-sale agent with dedicated tools to avoid any accidents.
carried out the
be
replaced, the operation must
be
to
or
damaged
is
the cable
If
•
or a single-pole circuit breaker. The method of connection is shown below.
The power supply should be connected in compliance with the relevant standard,
alterations. Any alterations must only be made by a qualified electrician.
suitable without
is
electrician whether the domestic wiring system
an
Check with
temperature will not exceed 75˚C at any point.
The power supply cable must not touch any hot parts and must be positioned so that its
devices, as they can cause overheating and fire.
branching
or
not use adapters, reducers,
do
the mains power supply,
to
connect the hob
To
the power supply cable sections can withstand the load specified on the rating plate.
3.
the voltage corresponds to the value given in the rating plate
2.
the domestic wiring system is suitable for the power drawn by the hob.
1.
Before connecting the hob to the mains power supply, check that:
a suitably qualified person.
by
mains power supply only
the
to
connected
be
This hob must
Connecting the hob to the mains power supply
28
-
EN
EN-27
• the isolating switch is easily accessible by the customer
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not
apply force onto the controls protruding from the hob.
Adjusting the bracket position
Fix the hob on the work surface by screw 4 brackets on the bottom case of hob
(see picture) after installation.
A
B
C
D
Screw
Bracket
Screw hole
Bottom case
Cautions
1. The induction hotplate must be installed by qualified personnel or technicians.
We have professionals at your service. Please never conduct the operation by
yourself.
2. The hob will not be installed directly above a dishwasher, fridge, freezer,
washing machine or clothes dryer, as the humidity may damage the hob
electronics
3.The induction hotplate shall be installed such that better heat radiation can be
ensured to enhance its reliability.
4. The wall and induced heating zone above the table surface shall withstand heat.
5. To avoid any damage, the sandwich layer and adhesive must be resistant to
heat.
Summary of Contents for CIES55MCTT/1
