background image

29

29

GENERAL ADVICE

• 

Before you begin cleaning, you must 

ensure that the appliance is switched 

off  and  disconnected  from  the 

electrical power supply.

• 

Important: The use of suitable 

protective clothing/gloves is 

recommended when handling or 

cleaning of this appliance.

• 

Under no circumstances should 

any  external  covers  be  removed  for 

servicing  or  maintenance  except  by 

suitable qualified personnel.

• 

It is advisable to clean when the 

appliance is cold and especially when 

cleaning the enamelled parts.

• 

Be very careful that no water penetrates 

inside the appliance.

• 

Avoid leaving alkaline or acidic 

substances (lemon juice, vinegar, etc.) 

on the surfaces.

• 

Avoid using cleaning products with a 

chlorine or acidic base.

• 

IMPORTANT: 

Do not use any abrasive 

products (e.g. certain types of sponge) 

and/or aggressive products (e.g. caustic 

soda, products containing corrosive substances), which could cause irreparable 

surface damage.

WARNING! When correctly installed, your product meets all safety requirements 

laid down for this type of product category. However special care should be taken 

around the underneath of the appliance as this area is not designed or intended to 

be touched and may contain sharp or rough edges, that may cause injury.

ENAMELLED SURFACES

All the enamelled parts must be cleaned with a sponge and soapy water only or other non-

abrasive products. Dry preferably with a microfibre or soft cloth.

If acid substances such as lemon juice, tomato conserve, vinegar etc. are left on the enamel 

for a long time they will etch it, making it opaque.

Do not shut lid when

burner alight. 

ATTENTION

Do not lower the glass lid when

the gas burner are  still  hot 

and  when  the  oven, installed 

below  the  cooking  hob,

is on or still hot.
Do  not  lay  on  the  glass  lid hot

pans and heavy kitchen utensils.
Dry  off  any  liquid which  may

have  spilt  on  the  cover  before

opening it. 

COOKING HOBS WITH

GLASS LID (optional)

CLEANING AND MAINTENANCE

3

Important: The manufacturer declines all liability for possible damage caused by

the use of unsuitable products to clean the appliance.

Attention! The appliance gets very hot, mainly around the cooking areas. It is very 

important that children are not left alone in the kitchen when you are cooking.

Do not use a steam cleaner because the moisture can get into the appliance thus 

make it unsafe.

Summary of Contents for CHG6PX SASO





































Reviews: