background image

14

14

GAS SECTION

2

CONNECTING THE COOKTOP TO THE GAS SUPPLY

The gas connection fitting (fig. 2.1) is made up of:

• 

the floating nut;

• 

the elbow;

• 

the gaskets;

The gas connection must be carried out by an authorised person according to the 

relevant local standards.

• 

If using a flexible hose, make sure it does not come into contact with moving parts.

• 

The rear of the chassis is recessed to provide a channel for the appliance inlet pipe.

• 

The gas connection fitting can be turned in the direction required (but never in a vertical 

or horizontal position) after loosening the elbow and floating nut connection.

• 

Never attempt to turn the elbow without having first loosened the floating nut.

• 

The supplied gaskets guarantee a good seal for the gas connection. We recommend 

that you replace the gaskets on the slightest sign of wear, deformation or imperfection.

• 

After connecting to the gas mains, check that the couplings are correctly sealed, using 

soapy solution, but never a naked flame.

GAS INSTALLATION REQUIREMENTS
Important!

• 

This  appliance  must  be  installed  and  serviced  only  by  a  suitably  qualified, 

registered installer. The installer shall refer to the local standards in force.

• 

Failure to install the appliance correctly could invalidate any manufacturer’s 

warranty.

• 

Before installation, make sure that the local distribution conditions (gas type and 

pressure) and the adjustment of this appliance are compatible. The appliance 

adjustment conditions are given on the plate or the label.

• 

If the gas pressure (for which the appliance is to be used) is variable or if it is 

not within the values indicated on the rating plate, it is mandatory to install a 

proper gas pressure regulator which must be adjusted to guarantee the correct 

operating pressure to the appliance (as per rating plate).

 

The regulator must be installed, adjusted and tested by a qualified technician.

• 

WARNING: Using the appliance with a wrong and/or variable gas pressure may 

be extremely dangerous and may result in serious injury to the user. Damage to 

the appliance could occur if not observing this condition.

 

The manufacturer declines every responsibility for any inconvenience resulting 

from the inobservance of this condition.

This appliance is supplied for use on LPG (PROPANE/BUTANE, 5 kPa; check the gas 

regulation label attached on the appliance).

Summary of Contents for CHG6PX SASO





































Reviews: