3
appliance, to replace the existing one, corresponding to the new gas adjustment. This label is contained in
the spare nozzle bag.
Table 1
Burner
Types of gas
Pressure
Nozzle diameter
Rater capacity
mbar
1/100
mm.
g/h
l/h
kW
kcal/h
Auxiliary Natural
G20
20
72
-
95
1
860
Butane
G30
30
50
73
-
1
860
Propane
G31
37
50
71
-
1
860
Semi-rapid Natural
G20
20
97
- 167
1,75 1505
Butane
G30
30
65
127
-
1,75
1505
Propane
G31
37
65
125
-
1,75
1505
Rapid Natural
G20 20 115 -
286
3
2580
Butane
G30
30
85
218
-
3
2580
Propane
G31
37
85
214
-
3
2580
Ultra rapid
Natural G20
20
153
-
405
4,25
3655
4 kW
Butane G30
30
102
309
-
4,25
3655
Propane
G31
37
102
303
-
4,25
3655
Natural G20
20
ext. 155
int. 70
-
-
476
5
-
4300
Ultra rapid
Dual 5 kW
Butane G30
30 ext.
96
int. 46
334 -
-
4,60 3956
Propane
G31
37 ext.
96
int. 46
328 -
-
4,60 3956
Table 2 (model with gas oven and gas grill with double controls)
Oven Natural
G20 20 155 -
429
4,50
3870
Butane
G30
30
105
327
-
4,50
3870
Propane
G31
37
105
321
-
4,50
3870
Grill Natural
G20 20 108
-
191
2
1720
Butane
G30
30
72
145
-
2
1720
Propane
G31
37
72
143
-
2
1720
Table 3 (model with gas oven and gas grill with single control,)
Oven Natural
G20 20 155 -
429
4,50
3870
Butane
G30
30
105
327
-
4,50
3870
Propane
G31
37
105
321
-
4,50
3870
Grill Natural
G20 20 108
-
191
2
1720
Butane
G30
30
72
145
-
2
1720
Propane
G31
37
72
143
-
2
1720
BURNER ADJUSTMENT
1) Burner "MINIMUM" adjustment:
Work surface burner adjustment
: follow the instructions below to adjust the work surface burner minimum:
1) Light the burner and set the knob to the MINIMUM position (small flame).
2) Remove the knob of the valve that is press fit on the rod of that valve.
3) If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the
valve rod (Fig. 8) and turn the choke screw to the right or left until the burner flame is adjusted to minimum. If the cooker is
equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see fig. 9).
4)For the gas valve of dual burner the choke valve is located on the valve body (fig.10), the A screw adjust the outer ring,
the B screw adjust the inner ring.
5) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.
Oven burner adjustment
: follow the instructions below to adjust the minimum:
1) Light the burner setting the knob to the MAXIMUM position.
2) Close the oven door and operate the oven for at least 10 minutes.
3) Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.
4) With a slotted screwdriver turn the choking screw (see figure 11) and, while observing the flame at the same time through the
cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the
MAXIMUM position.
Grill burner adjustment
: follow the instructions below to adjust the minimum:
1) Light the burner setting the knob to the MAXIMUM position.
2) Close the oven door and operate the oven for at least 10 minutes.
3) Set the knob to the MINIMUM position (small flame) and then remove it.
4) If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the
valve rod (Fig. 8) and turn the choke screw to the right or left, while observing the flame at the same time through the cooker
porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM
position. If the cooker is equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see
figure 9).
WARNING: The above-mentioned adjustment should be made only with natural gas burners, while for those operating
with liquid gas the screw must be locked at the end in a clockwise direction.
WARNING: For the model with single grill burner, the grill burner always operates at maximum and therefore no
minimum adjustment is required.