background image

Warranty

tel: 888-923-9813 | [email protected]| web: www.leisurecraft.com

Manufactured by:

Canadian Timber Collection Saunas warrants our saunas against defects in materials and 

workmanship under normal/residential use for a period of three (3) years, as applicable, from the 

date of receipt of the product by the original end-user consumer. This warranty does not apply to 

normal wear and tear and/or natural weather conditions. This warranty does not cover regular 

required maintenance of the sauna, (eg. Tightening bands on the barrels, cleaning or staining the 

sauna) refer to your sauna assembly manual for maintenance guidelines. This warranty does not 

cover misuse or negligence and the manufacturer and associated retailers are not liable for any 

injury or damage caused by the product. This warranty is a parts only warranty and any service or 

labor costs would not be considered as part of the 3 year warranty.

Purchaser Name: ________________________ Date: _______________ 

Purchased From: ________________________

41

Harmony Barrel Sauna

Assembly Instructions

Summary of Contents for Harmony Barrel










































Reviews: