Can-Am DS 450 X mx Operator'S Manual Download Page 105

Page: 105 / 152

MAINTENANCE PROCEDURES

vmo2008-011-073_a

1. Lock nut
2. Adjuster

NOTE:

Measure throttle free play at

the tip of throttle lever.

Tighten lock nut and reinstall protector.

vmo2008-011-001_c

1. Throttle lever

A. 2 mm to 4 mm (5/64 ft to 5/32 ft)

Spark Plugs

Spark Plugs Removal

Unplug spark plug cables.

vmo2008-011-082_a

CABLES LOCATION

Clean spark plugs and cylinder head
with pressurized air if possible.

WARNING

Always wear safety goggles when
using pressurized air.

Unscrew and remove spark plugs.

vmo2008-011-083_a

1. Spark plugs

Spark Plugs Installation

Prior to installation, make sure that
contact surfaces of cylinder head and
spark plugs are free of grime.

Using a feeler gauge, set spark plugs
gap

between

0.7 mm to 0.8 mm

(.028 in to .031 in).

______________

103

Summary of Contents for DS 450 X mx

























































































































































Search results

Summary of Contents for DS 450 X mx

Reviews:

Related manuals for DS 450 X mx

Brands by name

Popular brands

Can-Am DS 450 X mx, Operator'S Manual

Search results

Summary of Contents for DS 450 X mx

Reviews:

Related manuals for DS 450 X mx

Brands by name

Popular brands