Can-Am DS 450 X mx Operator'S Manual Download Page 108

Page: 108 / 152

MAINTENANCE PROCEDURES

Lights

Beam Aiming Adjustment

To adjust beam, proceed as follows.

1. Loosen the bolts shown on the fol-

lowing illustrations but do not re-
move them.

mmr2009-005-001_a

vmo2008-018-040_a

2. Adjust headlight housing angle by

hand.

3. Adjust both headlights evenly.

4. Tighten screw when proper adjust-

ment is reached.

Headlights Bulbs Replacement

NOTICE

Never touch glass portion

of a halogen bulb with bare fingers,
it shortens its operating life. If glass
is touched, clean it with isopropyl al-
cohol which will not leave a film on
the bulb.

NOTE:

Concerning the following il-

lustrations, the headlight housing has
been removed from the vehicle for a
better comprehension.

To replace the headlight bulb, proceed
as follows.

Turn the ignition switch to OFF posi-
tion.

Remove rubber protector from head-
light housing.

vmo2008-018-038_a

TYPICAL

1. Rubber protector

Unplug connector from headlight.

Push the retaining clip round ends for-
ward then set them on the sides to un-
lock headlight bulb.

106

______________

Summary of Contents for DS 450 X mx

























































































































































Search results

Summary of Contents for DS 450 X mx

Reviews:

Can-Am DS 450 X mx, Operator'S Manual, Page: 108 / 152

Search results

Summary of Contents for DS 450 X mx

Reviews: