Can-Am DS 450 X mx Operator'S Manual Download Page 31

Page: 31 / 152

OPERATION WARNINGS

WARNING

V00A0IQ

POTENTIAL HAZARD

Stalling, rolling backwards or improperly dismounting while climbing a hill.

WHAT CAN HAPPEN

Could result in vehicle overturning.

HOW TO AVOID THE HAZARD

Use proper gear and maintain steady speed when climbing a hill.

If you lose all forward speed:

Keep your weight uphill. Never open the throttle suddenly or make sudden
gear changes. The vehicle could flip over backwards.

Apply the brakes.

Lock parking brake after you have stopped.

Dismount on uphill side, or to a side if pointed straight uphill.

If you begin rolling backwards:

Keep your weight uphill. Never open the throttle suddenly or make sudden
gear changes. The vehicle could flip over backwards.

Never apply the rear brake while rolling backwards.

Apply the front brake gradually.

When fully stopped, apply rear brake as well and lock parking brake.

Dismount on uphill side, or to a side if pointed straight uphill.

Turn the vehicle around and remount, following the procedure described
further in this Operator's Guide.

________

SAFETY INFORMATION

________

Summary of Contents for DS 450 X mx

























































































































































Search results

Summary of Contents for DS 450 X mx

Reviews:

Can-Am DS 450 X mx, Operator'S Manual, Page: 31 / 152

Search results

Summary of Contents for DS 450 X mx

Reviews: