manualshive.com logo in svg

Can-Am 2008 DS 450, Operator'S Manual

The Can-Am 2008 DS 450 Operator's Manual is a comprehensive guide for all owners of this powerful ATV. Available for free download from our website, this manual provides detailed instructions, maintenance procedures, and invaluable tips, ensuring the optimal performance of your Can-Am 2008 DS 450.

Share
Download
background image

TABLE OF CONTENTS

While reading this Operator’s Guide, remember that:

WARNING

Indicates a potential hazard that, if not avoided, could result in serious in-
jury or death.

NOTICE. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

7

INTRODUCTION .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

SAFETY INFORMATION

SPECIAL SAFETY MESSAGES . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 10

OPERATION WARNINGS. . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 13

RIDING THE VEHICLE. . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 39

Pre-Operation Check . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 39
Clothing . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 41
Carrying Loads . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 42
Recreational Riding . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 42
Environment . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 42
Design Limitation . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 43
Off-Highway Operation. .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 43
General Operating and Safety Precautions . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 43
Uphill Driving .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 44
Downhill Driving .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 44
Side Hilling. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 44
Drop-Offs .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 44
Riding Techniques . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 44
Routine Maintenance. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 51

HANG TAG . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 52

IMPORTANT ON PRODUCT LABELS.. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 53

VEHICLE INFORMATION

HOW TO IDENTIFY YOUR VEHICLE . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 58

NOISE EMISSION CONTROL SYSTEM REGULATION . . . .. . . .. . . .. . . .. . . .. . . 59

EMISSION REQUIREMENTS . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 60

BREAK-IN PERIOD. . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 61

5-Hour Engine Oil and Filter Replacement . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 61
10-Hour Inspection . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 61

CONTROLS/COMPONENTS/INSTRUMENT. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 62

1) Throttle Lever .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 64

______________________

3

Summary of Contents for 2008 DS 450





















































































































































Reviews:

No comments

Related manuals for 2008 DS 450

IceCar B220 User And Maintenance Manual preview
B220
Brand: IceCar Pages: 37
BOMBARDIER Formula Mx 1988 Operator'S Manual preview
Formula Mx 1988
Brand: BOMBARDIER Pages: 62
BOMBARDIER traxter max series Operator'S Manual preview
traxter max series
Brand: BOMBARDIER Pages: 174
BOMBARDIER outlander max 800 Operator'S Manual preview
outlander max 800
Brand: BOMBARDIER Pages: 160
BOMBARDIER RALLY 200 2003 Shop Manual preview
RALLY 200 2003
Brand: BOMBARDIER Pages: 282
Can-Am outlander 400 series Operator'S Manual preview
outlander 400 series
Brand: Can-Am Pages: 156
Cold Jet Aero 40 HP Operator'S Manual preview
Aero 40 HP
Brand: Cold Jet Pages: 31
Yamaha VIKING YX70MPJ Owner'S Manual preview
VIKING YX70MPJ
Brand: Yamaha Pages: 170
Yamaha PRO HAULER YXP700 Owner'S Manual preview
PRO HAULER YXP700
Brand: Yamaha Pages: 92
Yamaha Grizzly YFM35FGIX Owner'S Manual preview
Grizzly YFM35FGIX
Brand: Yamaha Pages: 164
Ace Liberty s2585 Owner'S Manual preview
Liberty s2585
Brand: Ace Pages: 10
Omow ATV150-3 Owner'S Manual preview
ATV150-3
Brand: Omow Pages: 36
Suzuki LT80K4 Setup Manual preview
LT80K4
Brand: Suzuki Pages: 37
Clam Polar Trailer LG 7 Manual preview
Polar Trailer LG 7
Brand: Clam Pages: 5
Renegade 3OO ZTR Operator'S Manual preview
3OO ZTR
Brand: Renegade Pages: 19
KAYO MOTO A150 Assembly Manual preview
A150
Brand: KAYO MOTO Pages: 9
Kioti UD25-A0008A Installation Instructions Manual preview
UD25-A0008A
Brand: Kioti Pages: 8
Kioti MEC 2230SW Owner'S Manual preview
MEC 2230SW
Brand: Kioti Pages: 178

Brands by name

Popular brands

Load more brands