Camtec CPS-EC1500 Quick Start Manual Download Page 10 | Manualshive

Page: 10 / 13

background image

CPS-EC1500(R2) MANUAL

Camtec Power Supplies GmbH - Gewerbestrasse 30 - 76327 Pfinztal - Germany

P.10/13 (01/2017-02-1)

Phone +49(721)46596-0 - Fax +49(721)46596-77 -

www.camtec-gmbh.com

-

[email protected]

(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death)

Mechanics

Mechanics

Stable metal/aluminum housing IP20. To allow adequate convection, a free air space of 50mm (top/bottom) and
5mm (sidewalls) is required; for active devices 15mm space from the sidewalls. For free air convection it is
necessary to install the unit horizontal. Use the DIN-Rail installation (equipped standard) with the patented
35mm DIN-Rail brackets according to EN60275. It is easy to mount/dismount while snaping it onto the 35mm
DIN-Rail - no tools are necessary. A hard mount backplate (option) is available as well.

6

4

«
...
8
9
10
11
12
...
»

Summary of Contents for CPS-EC1500














Reviews:

No comments

Related manuals for CPS-EC1500

Brand: IBM Pages: 7

Brand: KAKA Industrial Pages: 10

Brand: Parkside Pages: 60

Brand: Parkside Pages: 68

Brand: Marson Pages: 11

Brand: Wacker Neuson Pages: 32

Brand: Urrea Pages: 6

Brand: Gude Pages: 20

Brand: Ryobi Pages: 124

6130-01-452-2777

Brand: Tesla Pages: 54

Brand: Tyco Electronics Pages: 8

Brand: Zipper Mowers Pages: 43

Brand: Chicago Pneumatic Pages: 52

Brand: Beckhoff Pages: 57

Brand: Westfalia Pages: 19

Brand: XPOtool Pages: 5

Brand: Hama Pages: 18

Brand: Wacker Neuson Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands