CAMSO CTS Installation Instruction Download Page 6 | Manualshive

Page: 6 / 20

CAMSO CTS Installation Instruction Download Page 6

CPB-435CNH Case and New Holland Combines (without speed multiplier)

Camso | 04-17 | 6

4.4 Oscillation Limiter Kit (Kit Part Number 2A-1083)

To prevent possible machine and/or undercarriage damage and additional downtime, it is required that the
oscillation limiters be installed. The oscillation limiters are there to reduce the possibility of the CTS track
over oscillating. The table below lists the parts that are included in the oscillation limiter kit which is
included in the fitment kit for your specific combine. If parts are missing or need to be replaced, please
contact your authorized Camso Dealer.

Item #

Part Number

Description

Quantity

1

2C-2421

¾” Spacer

4

2

2C-2426

Attachment Plate

2

3

2F-0031

M20 Washer

12

4

2F-0064

M16x2x60 Bolt 10.9

6

5

2F-0069

M20x2.5x100 Bolt 10.9

4

6

2F-0112

M16 Washer

12

7

2F-0130

M20x2.5x80 Bolt 10.9

8

8

2F-0310

M16 Nut

6

9

2M-066

Clevis

2

10

2S-0463

LH Oscillation Bracket

1

11

2S-0464

RH Oscillation Bracket

1

«
...
4
5
6
7
8
...
»

Summary of Contents for CTS





















Reviews:

No comments