manualshive.com logo in svg

CAMSO CTS, Installation Instruction, Page: 12 / 20

Share
Download
CAMSO CTS Installation Instruction Download Page 12

 

CPB-435CNH Case and New Holland Combines (without speed multiplier)  

Camso |  04-17  |  12  

 

b.  Combines without axle extensions installed. 

i.  Preferred CTS Installation 

•

  Install Axle Extensions onto 

combine. Please contact your 
local dealer for parts and 
instructions to install the axle 
extensions. 
 

ii.  Recommended CTS Installation 

(without axle extensions) 

•

  Bolt CTS directly to axle (with 

addition of the spacer plate 
included in the fitment kit).  

•

  Minor modifications to the 

combine will be required in 
order for the track to clear. 

•

 

NOTE:

 This allows 

approximately 2.5 ± 1 inch (65 ± 
25 mm) of clearance between the track and the combine. 

 

iii.  Optional CTS Installation (without axle extensions) 

•

  Use the spacer 

plate and adapter 
plate 

•

  Some 

modifications to 
the machine may 
be necessary to 
prevent track 
system from 
contacting 
combine. 

•

 

NOTE:

 This will 

allow 
approximately 7.5 
± 1 inch (190 ± 25 
mm) of clearance 
between the track 
and combine 

•

 

NOTE:

 Higher stress loads will be placed on the bolted joint  

•

 

NOTE:

 Limit high dynamic loading. Inspect bolted joint during daily 

inspection, especially if running with large headers and wet heavy 
crops 

•

 

NOTE:

 Additional parts will need to be purchased from Camso in 

order to install the CTS in this manner. 

 

Wheel/Track 

mounting flange 

CTS 

Drive 

Sprocket 

Adapter Plate 

Spacer Plate 

Summary of Contents for CTS





















Reviews:

No comments