CAMSO CTS Installation Instruction Download Page 13 | Manualshive

Page: 13 / 20

CAMSO CTS Installation Instruction Download Page 13

CPB-435CNH Case and New Holland Combines (without speed multiplier)

Camso | 04-17 | 13

WARNING

Should a motorized lifting device be used, assistance on ground during
operation of handling, coupling and assembly is needed.
Do not stay between lifting device and track and between track and combine
harvester.
Be careful: risk of injury.

9. Install the 3 or 4 reachable bolts in the

flange holes of the track and tighten
to 220 ft-lbs (300 Nm). Coat threads
of the bolt with engine oil prior to
installing.

NOTE:

The mounting bolts are

included in the fitment kit.

10. Repeat the operation on the

opposite side to install the second
track.

11. Once the machine is lowered to

the ground, move it forward or
backward slowly to uncover the remaining bolt holes.

12. Stop the machine and insert the remaining bolts on both track systems; tighten the bolts

to 220 ft-lbs (300 Nm). Coat threads of the bolt with engine oil prior to installing.

NOTE:

A 32 mm socket is provided with the fitment kit. This socket is necessary for the

socket to fit onto the head of the bolt and clear the CTS frame. Additional sockets are
available for purchase from Camso.

13. Finally, tighten all the bolts in cross sequence, moving the combine harvester

accordingly.

Mounting bolts should be torqued to 500 ft-lbs (670 Nm) for combines using

M22 bolts.

NOTE:

Mounting bolt torque should be checked regularly during use. Please reference

the SCHEDULED MAINTENANCE section of the the Operation and Maintenance Manual
(OMM) for additional information.

«
...
11
12
13
14
15
...
»

Summary of Contents for CTS





















Reviews:

No comments