camry CR 7329, User Manual

Page: 5 / 60

5
injury or damage to the device.
PRODUCT DESCRIPTION: FAN Cr7329
1. Propeller housing 2. Telescopic tripod
3. Tripod legs 4. Motor housing
5. Big pivot knob 6. Long bolt
7. Small fixing screw 8. Small adjustment knob
9. Speed control knob 10. Oscillation knob
11. Height adjustment knob
Assembly
1.In order to connect the tripod legs (3) to the telescopic tripod (2) look at picture A. Screw the three tripod legs (3) counterclockwise into
the tripod (2).
2.In order to assemble the motor housing (4) to the top of the tripod (2) look at picture B. First remove the big pivot knob (5) and the long
bolt (6) from the top of the telescopic tripod (2), then remove the fixing screw (7) and small adjustment knob (8) from the motor housing
(4) bracket.
3.Place the motor housing (4) on the top of the tripod (2) and thread the long bolt (6) through the bracket. Screw in the small retaining
screw (7) and tighten, but do not overtighten
4.Fit the big pivot knob (5) onto the end of the bolt (6) and the small adjustment knob (8) at the other side above the bolt. Tighten the
knobs while holding the motor housing (4) upright.
Operation
1.The fan is equipped with 3 speeds and an oscillation option. To use the fan, follow the simple instructions below. Place the fan on a dry,
flat surface where it will not overturn during use. Put three legs outwards as far as possible to keep the fan stable.
2.Make sure the speed control knob (9) on top of the motor housing is in the off position marked by zero. Then insert the power plug into
an appropriate electrical outlet.
3.Select the fan speed by changing the position of speed control knob (9) into desired speed:
0 - motor stopped, the device is switched off
1 - slow speed
2 - medium speed
3 - fast speed
4. Press the oscillation knob (10) on top of the motor housing (4) to activate the
oscillation function for wide air spread distribution. The propeller housing (1) will rotate from the left side to the right side. In order to com
back to stationary operation, pull up the knob (10) to stop oscillation when the propeller housing (1) is in the proper position.
5. In order to adjust the height of telescopic tripod (2) loosen the height adjustment knob (11) by turning it anticlockwise, next pull out or
push down the extension pole to the desired height, then tighten the knob (11) again firmly.
CLEANING AND MAINTENANCE
CAUTION: Do not allow the fan's motor part or any buttons to get wet.
1. Before cleaning remove the plug from the electrical socket.
2. Clean the outside housing by damp cloth with some mild detergent.
3. Store the fan in a dry place.
Technical Data:
Power: 50W
Max power: 100W
Voltage: 220-240V ~50-60Hz
DEUTSCH
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
DIESE FÜR DIE ZUKUNFT AUF
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund
von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2.Das Gerät ist nur für den Hausgebrauch verwendet. Verwenden Sie es nicht für andere
Zwecke als den bestimmungsgemäßen Gebrauch.
3.Das Gerät ausschließlich an die Steckdose 2 2 0 -240 V ~ 50 /60 Hz anschließen. Es darf
nicht zu anderen, bestimmungswidrigen Zwecken benutzt werden. Wegen
Vorsichtsmaßnahmen, sollten keine weiteren Geräte an den gleichen Stromkreis
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container
Worn device should be returned to the appropriate point storage because it is dangerous in the device
ingredients may pose a threat to the environment. The electrical device should be handed over to limit
its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.