manualshive.com logo in svg

Campersat Campersat Autoseek Autoskew System 4441, Supplementary Installation Handbook

Share
Download
Campersat Campersat Autoseek Autoskew System 4441 Supplementary Installation Handbook Download Page 2

Campersat AutoSeek Autoskew   

2

H4441 Build 4441 August 2008

Version 1/2008

Installation Instructions

A

utoseek Auto Skew CI

FITTING INSTRUCTIONS Autoseek Autoskew

It is no problem to fit an Autoseek Autoskew fully automatic satellite system onto any

vehicle. However, you should take care with some specific points and therefore, PLEASE

READ these instructions carefully before starting your work, to obtain the very best

results later on whenever you use your new system.
Please read each topic in this manual carefully, before performing the work described

there. Go through the topics step by step.
Attention:
Highly sensitive device. Never apply any external force to the dish bracket or the LNB

arm.  Any  movement  of  the  dish  will  happen  automatically.  Do  not  lift  or  rotate

manually. Do not carry the system on the dish, the LNB or any of the cables. Always hold

it on the plastic body or the aluminium mounting plate. Do not remove any of the

screws on the plastic body.

Summary of Contents for Campersat Autoseek Autoskew System 4441















Reviews:

No comments

Brands by name

Popular brands

Load more brands