background image

11

Operating Instructions and Assembly Instructions 

Airless Paint Sprayers

ClEANUP FOr ChANGING PAINTS 

Or TEmPOrAry STOrAGE FOr 

mOrE ThAN ONE NIGhT

wEAr All NECESSAry 

SAFETy GEAr

NECESSAry TOOlS / mATErIAlS:

•  Pliers
•  Rag
•  Gloves
•  Two (2) buckets
•  At least one (1) gallon of cleaning 

fluid

•  cleaning brush

NOTE: 

 Do NOT disconnect any hoses.

NOTE: 

 Refer to coating manufacturer 

for recommended cleaning fluid.

1.  Turn prime/spray control to PRIME 

position.

2.  Turn power switch to ON.

 

High pressure 

  hose may still be 

pressurized with prime/spray control 

in the pRiME position. with the gun 

pointed in a safe direction, pull the 

gun trigger to relieve any pressure in 

the hose.

3.  Turn pressure to HIGH (completely 

clockwise).

4.  Tilt unit back, lift suction assembly 

above fluid level in bucket.

 

While holding suction assembly 
above paint level, allow pump to 
run until empty.

5.  Immediately place both suction 

assembly and bypass tube in a 
bucket containing enough cleaning 
fluid to cover suction bell by two 
inches. Allow pump to prime and 
begin circulating fluid.

6.  While fluid is circulating, soak rag 

in fluid and wipe exterior of suction 
assembly and bypass tube. Remove 
suction filter with pliers. Wipe 
inside of suction filter housing with 
rag removing excess paint buildup. 
Clean both sides of suction filter 
with rag and reinsert filter into 
suction filter housing.

NOTE:

 Do NOT allow fluid to circulate 

for more than 15 minutes.

Cleaning Pump

Turn Pressure to HIGH  

(completely clockwise)

3

4

Lift Suction Assembly above 

Paint Level in Bucket

www.chpower.com

Turn Prime/Spray 

Control to PRIME 

Position

1

6

Wipe Exterior of Suction 

Assembly and Bypass Tube

Suction Assembly and 

Bypass Tube in Bucket

of cleaning fluid

11

2

Turn  power switch to ON 

(shown in the OFF position)

5

Summary of Contents for PS230B

























Reviews: