background image

8

Preparation (Continued)

10. After completing the flush/testing 

process, purge the pump of fluid.

11. Repeat the preceding steps using 

paint instead of cleaning solvent.

NOTE:

 Strain and thin paint before 

using. All paint may have particles that 
will clog filter and spray tips. Remove 
any skin which may have developed on 

Operating Instructions and Assembly Instructions 

Airless Paint Sprayers

www.chpower.com

the paint due to air exposure. Follow 
paint manufacturers’ recommendations 
on thinning paint. 
12. When pure paint appears from 

spray tip rotate tip to the SPRAY 
position. The system is now ready 
for use.

CLEAN Position

1

SPRAY Position

2

12”

Holding Spray Gun

Thin Coat

Thin Coat

Heavy 

Coat

Over-
spray

Over-
spray

Result of Flexing Wrist While Spraying

Approx. 

10-12”

Start 
Stroke

Pull 

Trigger

Release 

Trigger

End 

Stroke

Proper Way to Trigger Spray Gun

INCO

rrEC

T

Spraying Instructions

Professional looking results can be 
obtained by following the spray tips 
below.
1.  Keep the gun perpendicular to the 

surface.

 

Always hold the gun perpendicular 
to the surface with the tip 
approximately 12 inches from the 
surface. If held at an angle (up 
and down or side to side), paint 
will build up unevenly, leave the 
work splotchy, and cause excessive 
overspray  (See Figure to the right).

2.   Move with a smooth arm stroke.
 

Move the gun at a steady, even 
pace while keeping the gun 
perpendicular to the surface (See 
Figures to the right). Do not fan 
the gun. Fanning the gun will cause 
excessive overspray and uneven 
coverage (See Figure to the right).

3.  Start moving the gun before 

triggering.

 

To get a smooth overlap and prevent 
initial paint buildup, start your 
stroke movement before pulling the 
trigger. Release the trigger before 
stopping at the end of the stroke 
(See Figure to the right).

NOTE:

 To assure uniform paint 

coverage, overlap each stroke by 20% 
- 30% and use two coats with a cross 
pattern (one coat horizontal, second 
coat vertical).

Prevent clogged tip

Water

Summary of Contents for PS230B

























Reviews: