4. Reconnect air
supply to the
nailer.
5. Depress the
Work Contact
Element (WCE)
against the
work surface
without pulling
the trigger. The nailer
MUST NOT
OPERATE
. Do not use the tool if it
operates without pulling the
trigger. Personal injury may result.
6. Remove the
nailer from the
work surface.
The Work
Contact
Element (WCE)
must return to
its original down position. The
nailer
MUST NOT OPERATE
. Do not
use the tool if it operates while
lifted from the work surface.
Personal injury may result.
7. Pull the
trigger and
depress the
work
contact
element
(WCE) against the work surface. The
nailer
MUST NOT OPERATE
.
8. Depress
the Work
Contact
Element
(WCE)
against the
work surface. Pull the trigger. The
nailer
MUST OPERATE
.
LOADING THE NAILER
1. Always
connect
the tool to the air
supply before
loading
fasteners.
2. Insert one stick
of nails into
rear loading
slot while
holding tool
down so nails
will slide
forward in
magazine.
NOTE:
Make
certain to insert
nail heads into
wide area at top of magazines with
nail points down.
Operating The Nailer
(Continued)
Operational Modes
Always know the
operational mode
of the nailer before using. Failure to
know the operational mode could
result in death or serious personal
injury.
THIS TOOL IS SOLD WITH A BLACK
SINGLE CYCLE TRIGGER. THIS TOOL
IS NOT INTENDED TO BE USED WITH
A RED BUMP CYCLE TRIGGER.
SINGLE CYCLE MODE
This method is
recommended
for precise nail
placement. This
mode requires
the trigger to
be pulled each time a nail is driven. The
nailer can be actuated by depressing
the WCE against the work surface
followed by pulling the trigger. Or the
nailer can be actuated by pulling the
trigger and then depressing the WCE
against the work surface.
The trigger must be released to reset
the tool before another nail can be
driven.
WORK CONTACT ELEMENT (WCE)
Check the opera-
tion of the Work
Contact Element (WCE) trip mechanism
before each use. The WCE must move
freely without binding through its
entire travel distance. The WCE spring
must return the WCE to its fully
extended position after being
depressed. Do not operate the nailer if
the WCE trip mechanism is not
operating properly. Personal injury may
occur.
1. Disconnect the
air supply from
the nailer.
2. Remove all
nails from the
magazine (see
Loading/
Unloading).
3. Make sure the
trigger and
work contact
element (WCE)
move freely up
and down
without sticking or binding.
!
CAUTION
!
WARNING
3. Press “Nail
Bypass Button”
in round hole in
the Nail Pusher
Mechanism and
pull back. This
allows the nail
clip to slide fully into the magazine.
4. Release the pusher. Allow pusher to
rest against nails. The nailer is now
loaded.
UNLOADING THE NAILER
1. Always unload all fasteners before
removing tool from service.
Unloading
is the reverse of
loading, except always
disconnect
the air hose before unloading.
2. Pull nail pusher
mechanism back
and press “Nail
Bypass Button.”
3. Hold tool
upright so nails
will slide out of
magazine.
4. Release the
Pusher.
ADJUSTING THE NAIL PENETRATION
The IFN35650 is equipped with an
adjustable depth of drive feature. This
allows the user to determine how deep a
fastener will be driven into the work
surface.
1. Adjust the
operating
pressure to
a pressure
which will
consistently
drive the
fasteners. Do not exceed the
maximum operating pressure of the
nailer of 110 psi.
2
1
1
2
2
1
4
Model IFN35650
Operating Instructions
www.chpower.com
Nail Pusher
Mechanism
Slot
Nail Bypass Button
Pusher
Mechanism
Nail
Nail Bypass Button
COUNTER-
CLOCKWISE
CLOCKWISE
Movement
