background image

CAMEC ELITE PRO

®

 2

 

EM305

Ref: ELITE PRO 2 EM305-0715Rev.A.

19

•  Check the battery of the remote control handset. If empty, renew the 9V battery.

•  Caravan battery could be empty. If empty, recharge completely or renew caravan battery before taking any further 

action.

•  Caravan battery could be overloaded. Check your charging equipment and try to discharge the battery by  

connecting/using a light or any other load. If this does not give any result, renew caravan battery before taking any 

further action. 

•  Check the distance between the remote control and the caravan is not more than 5 metres. If there is no signal 

between the remote control handset and the control unit, the manoeuvring system will not function at all and the 

green LED on handset will blink.

• 

Check if there is any distortion signal (other transmitter, high power cables, Wifi etc.) that disturbs a good 

 

communication between remote control handset and control unit. If there is no good communication between the 

control unit and remote control handset, the manoeuvring system will not function and the green LED on remote 

control handset will blink.

In general, all error messages will reset automatically after one minute. If this is not the case, reset the electronics 

of the manoeuvring system by switching off the manoeuvring system via the isolation switch and the remote control 

handset for at least 15 seconds and then turn them on again.

Unit fails to operate or moves intermittently:

•  Check the battery of the remote control. If empty, renew the 9V battery.

•  Caravan battery could be empty. If empty, recharge completely or renew caravan battery before taking any further 

action.

•  Caravan battery could be low - with the rollers engaged. Check the voltage drop on the caravan battery, if this 

drops well below 10 volts, charge or renew caravan battery

•  Caravan battery could be overloaded. Check your charging equipment and try to discharge the battery by  

connecting/using a light or other load. If this does not give any result, renew caravan battery before taking any 

further action.

•  Check the cable-connection between the caravan battery and the control unit.

•  Badly connected or corroded battery terminals can cause intermittent problems, check battery terminals, clean 

and connect again.

•  Check the distance between the remote control and the caravan is not more than 5 metres. If there is no signal 

between the remote control handset and the control unit, the manoeuvring system will not function at all and the 

green LED on handset will blink.

• 

Check if there is any distortion signal (other transmitter, high power cables, Wifi etc.) that disturbs a good 

 

communication between remote control handset and control unit. If there is no good communication between the 

control unit and remote control handset, the manoeuvring system will not function and the green LED on remote 

control handset will blink.

In general, all error messages will reset automatically after one minute. If this is not the case, reset the electronics 

of the manoeuvring system by switching off the manoeuvring system via the isolation switch and the remote control 

handset for at least 15 seconds and then turn them on again.

Roller will not turn, spindle rotates freely:

•  The motor or gear is broken, please contact your 

Camec Elite Pro

®

 2

 EM305 supplier.

In case of any doubt, please call your Camec Elite Pro

®

 2 supplier.

Summary of Contents for Elite Pro2 EM305





















Reviews: