p.
22
- M
an
u
al
c
od
e:
11
9
P
M
7
5
11
9
P
M
7
5
v.
44
1
0
/2
0
14 © C
A
M
E S
.p.
A
. - T
h
e d
ata a
n
d i
n
fo
rm
ati
on i
n th
is
m
an
u
al
m
ay b
e c
h
an
g
ed at a
ny ti
m
e a
n
d w
ith
ou
t n
oti
ce
.
ENGLISH
WARNING!
important safety instructions for people:
READ CAREFULLY!
Premise
• Employ this product only for the use for which it was expressly made. Any
other use is dangerous. CAME S.p.A is not liable for any damage caused by
improper, wrongful and unreasonable use • Keep these warnings together
with the installation and operation manuals that come with the operator.
Before installing
(checking what's there: if something is missing, do not continue until you
have complied with all safety provisions)
• Check that the automated parts are in good mechanical order, that the
operator is level and aligned, and that it opens and closes properly. Make
sure you have suitable mechanical stops • If the operator is to be installed
at a height of over 2.5 m from the ground or other access level, make
sure you have any necessary protections and/or warnings in place • If any
pedestrian openings are fi tted into the operator, there must also be a system
to block their opening while they are moving • Make sure that the opening
automated door or gate cannot entrap people against the fi xed parts of the
operator • Do not install the operator upside down or onto elements that
could yield and bend. If necessary, add suitable reinforcements to the an-
choring points • Do not install door or gate leaves on tilted surfaces • Make
sure any sprinkler systems cannot wet the operator from the ground up •
Make sure the temperature range shown on the product literature is suitable
to the climate where it will be installed • Follow all instructions as improper
installation may result in serious bodily injury • It is important to follow these
instructions for the safety of people.
Installing
• Suitably section off and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and children
• Be careful when handling operators that weigh over 20 kg. If need be, use
proper safety hoisting equipment • All opening commands (that is, buttons,
key switches, magnetic readers, and so on) must be installed at least 1.85
m from the perimeter of the gate's working area, or where they cannot be
reached from outside the gate. Also, any direct commands (whether but-
tons, touch panels, and so on) must be installed at least 1.5 m from the
ground and must not be reachable by unauthorized persons • All maintained
action commands, must be fi tted in places from which the moving gate lea-
ves and transit and driving areas are visible • Apply, if missing, a permanent
sign showing the position of the release device • Before delivering to the
users, make sure the system is EN 12453 standard compliant (regarding
impact forces), and also make sure the system has been properly adjusted
and that any safety, protection and manual release devices are working
properly • Apply Warning Signs (such as the gate's plate) where necessary
and in a visible place.
Special user-instructions and recommendations
• Keep gate operation areas clean and free of any obstructions. Make sure
that the photocells are free of any overgrown vegetation and that the ope-
rator's area of operation is free of any obstructions • Do not allow children
to play with fi xed commands, or to loiter in the gate's maneuvering area.
Keep any remote control transmitters or any other command devices away
from children, to prevent the operator from being accidentally activated.
The apparatus may be used by children of eight years and above and by
physically, mentally and sensorially challenged people, or even ones without
any experience, provided this happens under close supervision or once they
have been properly instructed to use the apparatus safely and to the poten-
tial hazards involved. Children must not play with the apparatus. Cleaning
and maintenance by users must not be done by children, unless properly
supervised • Frequently check the system for any malfunctions or signs of
wear and tear or damage to the moving structures, to the component parts,
all anchoring points, including cables and any accessible connections.
Keep any hinges, moving joints and slide rails properly lubricated • Perform
functional checks on the photocells and sensitive safety edges, every six
months. To check whether the photocells are working, wave an object in
front of them while the gate is closing; if the operator inverts its direction
of travel or suddenly stops, the photocells are working properly. This is the
only maintenance operation to do with the power on. Constantly clean the
photocells' glass covers using a slightly damp cloth; do not use any sol-
vents or other chemical products that may ruin the devices • If repairs or
modifi cations are required to the system, release the operator and do not
use it until safety conditions have been restored • Cut off the power supply
before releasing the operator for manual openings and before any other
operation, to prevent potentially hazardous situations. Check the instruc-
tions • If the power supply cable is damaged, it must be replaced by the
manufacturer or authorized technical assistance service, or in any case, by
similarly qualifi ed persons, to prevent any risk • It is FORBIDDEN for users to
perform any OPERATIONS THAT ARE NOT EXPRESSLY REQUIRED OF THEM
AND WHICH ARE NOT LISTED in the manuals. For any repairs, modifi cations
and adjustments and for extra-ordinary maintenance, CALL TECHNICAL
ASSISTANCE • Log the jobs and checks into the periodic maintenance log.
Further recommendations for all
• Keep away from hinges and mechanical moving parts • Do not enter
the operator's area of operation when it is moving • Do not counter the
operator's movement as this could result in dangerous situations • Always
pay special attention to any dangerous points, which have to be labelled with
specifi c pictograms and/or black and yellow stripes • While using a selector
switch or a command in maintained actions, keep checking that there are no
persons within the operating range of any moving parts, until the command
is released • The gate may move at any time and without warning • Always
cut off the power supply before performing any maintenance or cleaning
Danger of hand crushing
Danger! High voltage.
No transiting while gate is moving
