ENGLISH
5 6
5 6
Immunity
5 6
snow
mode
5 6
normal
heavy
snow
mode
3 4
3 4
3 4
3 4
Position
1
Position
2
Position
3
Position
4
3
2
0
1.0m
2.0m
1.0m
1
8
2
7
3
6
4 5
0
1.0m
1.0m
2.0m
3.0m
2.8m
2.6m
2.4m
2.2m
2.0m
1.0m
3.0m
2.8m
2.6m
2.4m
2.2m
2.0m
1.0m
1
8
2
7
3
6
4 5
0
1.0m
1.0m
3.0m
2.8m
2.6m
2.4m
2.2m
2.0m
1.0m
1
2 3 4
8
7
6
5
Adjusting the Pattern Width
Pattern when changed 7
to Right
Pattern when changed 7
to Left
Pattern when Standard
1
ADJUSTMENT
Note
Setting the pattern for exact door opening may give a slow response to side approaching traffic.
: Erasable
Area
: Erasable
Area
: Erasable
Area
Setting the Width
adjustment shutters
Adjusting the Width Angle
Left or Right : between 0
to 7
(3.5
per click)
to Left
O p e n s
A l l A r e a s
Eliminate
1 2 7 8
7 8
1 2
Eliminate
Eliminate
to Right
Setting the Row with the
Dipswitch 7 & 8.
Pattern when changed 4
to Deep (outside).
Pattern when changed -4
to Shallow (inside).
Pattern when Standard
0m
1.0m
2.0m
1.0m
2.0m
2.2m
2.4m
2.6m
2.8m
3.0m
0m
1.0m
2.0m
1.0m
2.0m
2.2m
2.4m
2.6m
2.8m
3.0m
0m
1.0m
2.0m
1.0m
2.0m
2.2m
2.4m
2.6m
2.8m
3.0m
0m
1.0m
2.0m
1.0m
2.0m
2.2m
2.4m
2.6m
2.8m
3.0m
Adjusting the Pattern Depth
7 8
4ROW
3ROW
2ROW
1ROW
7 8
7 8
7 8
: Erasable
Area
: Erasable
Area
: Erasable
Area
1st
2nd
3rd
4th
1st
2nd
3rd
4th
1st
2nd
3rd
4th
1 2
1 2
15sec.
1 2
180sec.
1 2
2sec.
1 2 3 4 5 6 7 8
ON
L M H
L M H
Setting of Sensitivity Switch and Dipswitches
Sensitivity Switch
Dipswitches
Setting the Sensitivity
Normally set to “M.”
“H” increases the sensitivity and “L” lowers the sensitivity.
Setting the Presence timer
1st Row and 2nd Row from
door provide the presence detection.
(1) Select the presence detection time.
(2) Turn the power off and on again. Otherwise it may
leave door open for the duration of the presence time
set.
(3) After making sure that the door closes, wait for 10
seconds before entering the detection area to set the
Presence timer.
Setting the Frequency Function
(Interference Prevention)
Four different frequencies can be
set by adjusting the Dipswitch 3
and 4.
Note
When two or more sensors are installed close to each
other, it is possible that they interfere. When that happens,
change the Frequency.
Setting the Snow mode
Set the Dipswitch5 and 6 to snow
mode , if the sensor is used in a
region with snow or a lot of insects.
Adjusting the Depth
Angle between -4 to 4
(1
per click).
Shallow
Note
Set the pattern for actual traffic. It may cause slow activation for the traffic from the front, when the Row is eliminated.
Depth
