TROUBLE
POSSIBLE CAUSE
SOLUTION
NE DOES NOT
OPERATE
Power supply is not adequate.
Adjust to stated voltage.
Connection Failure.
Check the wiring and the connector.
DOSE NOT OPERATE
CONSISTENTLY
Dirty detection window.
Wipe the detection window with a damp cloth. (Do not use any
cleaner or solvent.)
Sensitivity is Low.
Set the Sensitivity Switch “H.”
OPERATES BY ITSELF
(GHOSTING)
There is an object that moves or emits light in the detection area.
(Ex. plant, illumination, etc.)
Remove the object.
Vibration of the header.
Secure the header. Or set the Sensitivity Switch “L.”
Sensitivity is high.
Set the Sensitivity Switch “L.”
Waterdrops on detection window.
Install in a place keeping the waterdrops off. OR use a rain-cover
(Optional).
Detection area has interfered the area of another sensor.
Set the different frequency position each other.
The detection 1st row spots are overlapping with the door / header.
Adjust the detection area to deep (outside).
There is an refl ected object in the detection area. Solar light
refl ects.
Remove the object.
There was a puddle left by rain or snow. The fl oor has gotten wet.
This sensor is equipped with the anti-malfunction. However, pay
attention when installing as malfunction may occur under the left
conditions.
The exhaust of the car and the fog penetrate into the detection
area.
DOOR STAY OPEN OR
CLOSED
Presence timer is Infi nity. There was an abrupt condition change in
the detection area.
Turn the power off and on again.
Contact your installer or the sales engineer if:
- the trouble still persists after checking and remedying as described above.
DECLARATION CE OF CONFORMITY
Pursuant to the Electromagnetic
compatibility Directive
CAME CANCELLI AUTOMATICI S.p.A.
Via Martiri della Libertà, 15
31030 Dosson di Casier
TREVISO - ITALY
Is fully liable in declaring that the
products listed below:
MR8003
comply with the National Law related
to the following European Directives
and to the applicable parts of the
following Standards:
Electromagnetic compatibility Directive
Construction products Directive
-----
Reference code to
request a true copy
of the original
All data checked with the maximum care. However, no liability is accepted for any error or omission.
The declaration de conformity and other technical documentation are available on our website www.came.it -
BUY-TO-SELL PRODUCT
2004/108/CE
2006/95/CE
EN 13241-1 / EN 61000-6-2 / EN 61000-6-3
EN 300 330-2 / EN 300 440 / EN 300 440-2
EN 300 683 / EN 301 489-1 / EN 301 489-3
EN 50081-1 / EN 50081-2 / EN 50392
EN 60335-1 / EN 60335-2-103
EN 60950 / EN 60950-1
The Managing Director
Gianni Michielan
DDC E EN
R001
ENGLISH
TROUBLESHOOTING
Note
The door may open once after the power is switched on.
Inform the following items to the building
owner/operator
1. When turning the power on, always walk-test the sensor pattern to ensure proper operation.
2. Always keep the detection window clean. If dirty, wipe the window with a damp cloth. (Do not use any cleaner or solvent.)
3. Do not wash the sensor with water.
4. Do not disassemble, rebuild or repair the sensor yourself; otherwise electric shock may occur.
5. Contact your installer or the sales engineer if you want to change the settings.
6. Do not place an object that moves or emits light in the detection area. (Ex. Plant, illumination, etc.)
7. Do not paint the Detection Window.
Entry motion
Power OFF
Outside the
Detection area
Entry into 3rd or
4th Row
(image)
Sensor status
Power OFF
Stand-by
Motion
Detection Active
Entry into 2nd Row Entry into 1st
Row
Outside the
Detection area
Motion or Presence
Detection Active
Stand-by
Orange
Red
Green
Yellow
Green
White
Output
Operation indicator
Green
OFF
Yellow
Green
White
Yellow
Green
White
Yellow
Green
White
CHECKING
Check the operation according to the chart below.
CAME
CANCELLI AUTOMATICI S.P.A.
V
IA
M
ARTIRI
D
ELLA
L
IBERTÀ
, 15
31030 D
OSSON
DI
C
ASIER
Treviso -
ITALY
(+39) 0422 4940
(+39) 0422 4941
A
SSISTENZA
T
ECNICA
N
UMERO
V
ERDE
800 295830
W
EB
www.came.it
E-
w w
w. c
a m e
. c o m
w w
w. c
a m e
. c o m
