LO
CK
UN
LO
CK
LO
CK
UNL
OC
K
ENGLISH
p.
22
-
M
an
u
al
c
od
e:
11
9
D
S
5
5
E
N
11
9
D
S
5
5
E
N
ve
r.
44
01
/2
01
5
© C
A
M
E S
.p.
A
. - T
h
e d
ata a
n
d i
nf
or
m
ati
on i
n th
is
m
an
u
al
m
ay b
e c
h
an
g
ed at a
ny ti
m
e a
n
d C
A
M
E S
.p.
A
. i
s u
n
d
er n
o o
b
lig
ati
on
to i
nf
or
m u
se
rs of s
ai
d c
h
an
g
es
Premise
• Employ this product only for the use for which it was expressly made.
Any other use is dangerous. CAME S.p.A. is not liable for any damage cau-
sed by improper, wrongful and unreasonable use • Keep these warnings
together with the installation and operation manuals that come with the
operator.
Before installing
(checking what's there: if your evaluation is negative, do not proceed be-
fore having complied with all safety requirements)
• Check that the automated parts are in good mechanical order, that the
operator is level and aligned, and that it opens and closes properly. Make
sure you have suitable mechanical stops • If the operator is to be installed
at a height of over 2.5 m from the ground or other access level, make
sure you have any necessary protections and/or warnings in place • If
any pedestrian openings are fi tted into the operator, there must also be a
a system to block their opening while they are moving • Make sure that
the opening automated door or gate cannot entrap people against the fi xed
parts of the operator • Do not install the operator upside down or onto
elements that could yield and bend. If necessary, add suitable reinforce-
ments to the anchoring points • Do not install door or gate leaves on tilted
surfaces • Make sure any sprinkler systems cannot wet the operator from
the ground up • Make sure the temperature range shown on the product
literature is suitable to the climate where it will be installed • Follow all
instructions as improper installation may result in serious bodily injury •
It is important to follow these instructions for the safety of people. Keep
these instructions.
Installing
• Suitably section off and demarcate the entire installation site to pre-
vent unauthorized persons from entering the area, especially minors and
children • Be careful when handling operators that weigh over 20 kg. If
need be, use proper safety hoisting equipment • All opening commands
(that is, buttons, key switches, magnetic readers, and so on) must be
installed at least 1.85 m from the perimeter of the gate's working area,
or where they cannot be reached from outside the gate. Also, any direct
commands (buttons, touch panels, and so on) must be installed at least 1.5
m from the ground and must not be reachable by unauthorized persons
• All maintained action commands, must be fi tted in places from which
the moving gate leaves and transit and driving areas are visible • Apply,
if missing, a permanent sign showing the position of the release device •
Before delivering to the users, make sure the system is EN 12453 standard
compliant (regarding impact forces), and also make sure the system has
been properly adjusted and that any safety, protection and manual release
devices are working properly • Apply Warning Signs (such as the gate's
plate) where necessary and in a visible place
Special user-instructions and recommendations
• Keep gate operation areas clean and free of any obstructions. Make
sure that the photocells are free of any overgrown vegetation and that
the operator's area of operation is free of any obstructions • Do not allow
children to play with fi xed commands, or to loiter in the gate's maneuve-
ring area. Keep any remote control transmitters or any other command
device away from children, to prevent the operator from being accidentally
activated. • The apparatus may be used by children of eight years and
above and by physically, mentally and sensorially challenged people, or
even ones without any experience, provided this happens under close su-
pervision or once they have been properly instructed to use the apparatus
safely and about the potential hazards involved. Children must not play
with the apparatus. Cleaning and maintenance by users must not be done
by children, unless properly supervised • Frequently check the system
for any malfunctions or signs of wear and tear or damage to the moving
structures, to the component parts, all anchoring points, including cables
and any accessible connections. Keep any hinges, moving joints and slide
rails properly lubricated • Perform functional checks on the photocells and
sensitive safety edges, every six months. To check whether the photocells
are working, wave an object in front of them while the gate is closing; if
the operator inverts its direction of travel or suddenly stops, the photocells
are working properly. This is the only maintenance operation to do with
the power on. Constantly clean the photocells' glass covers using a slightly
water-moistened cloth; do not use any solvents or other chemical products
that may ruin the devices • If repairs or modifi cations are required to the
system, release the operator and do not use it until safety conditions have
been restored • Cut off the power supply before releasing the operator for
manual openings and before any other operation, to prevent potentially
hazardous situations. Read the instructions • If the power supply cable
is damaged, it must be replaced by the manufacturer or authorized tech-
nical assistance service, or in any case, by similarly qualifi ed persons, to
prevent any risk • It is FORBIDDEN for users to perform any OPERATIONS
THAT ARE NOT EXPRESSLY REQUIRED OF THEM AND WHICH ARE NOT LI-
STED in the manuals. For any repairs, modifi cations and adjustments and
for extraordinary maintenance, CALL TECHNICAL ASSISTANCE • Log the
job and checks into the periodic maintenance log.
Additional special recommendations for everyone
• Keep away from hinges and mechanical moving parts • Do not enter
the operator's area of operation when it is moving • Do not counter the
operator's movement as this could result in dangerous situations • Always
pay special attention to any dangerous points, which have to be labeled
with specifi c pictograms and/or black and yellow stripes • While using a
selector switch or a command in maintained actions, keep checking that
there are no persons within the operating range of any moving parts, until
the command is released • The gate may move at any time and without
warning • Always cut off the power supply before performing any main-
tenance or cleaning.
Danger of hand crushing
Danger! High voltage.
No transiting while maneuvering
WARNING!
important safety instructions for people:
READ CAREFULLY!
Danger of foot crushing
