CAMBRIDGE CSW-15AT Installation, Setup And Operation Instructions Download Page 4

Page: 4 / 14

1.0 OPERATION

1.1 Key Functions:

ZERO

Brings the scale to a zero balance reading. If the

ZERO

key

is pressed and held for 5 seconds the Calibration zero value

will be displayed.

GRS/NET

Toggles the display between Gross weight and Net weight.

This key is also used to enter Setup & Calibration Mode.

To enter, press and hold this key until the Parameter (

P xxx

)

Event counter is displayed, then release. Immediately after

CodE

is displayed, enter in sequence (within 5 seconds)

TARE

lb/kg

GRS/NET

, and

PRINT/ENTER

. The display will

indicate

ScAlE

and you are now in Setup & Calibration mode.

Note: P xxx and C xxx are event counters that will

increment each time one or more changes are made

to the Scale or Calibration Parameters.

TARE

Enters the Gross weight value into the Tare display and switches

to the net display mode. If the

TARE

key is pressed and held for 5

seconds the current Tare value will be displayed.

Lb/kg

Toggles the display between pounds and kilograms.

1.2 Error Messages:

ScnEg

When the weight is more than 10 divisions negative from the zero
calibration point.

OLD

The scale is in an overload condition.

BAtLo

Will flash when the battery voltage falls to 10.8VDC and will be
displayed constantly when the voltage falls to 10.2VDC.

Err d

More than 5000 scale divisions have been selected in

Ntep or

Angle mode. More than 20,000 scale divisions have been selected in

No Mode.

Summary of Contents for CSW-15AT















Search results

Summary of Contents for CSW-15AT

Reviews:

Related manuals for CSW-15AT

Brands by name

Popular brands

CAMBRIDGE CSW-15AT, Installation, Setup And Operation Instructions

Search results

Summary of Contents for CSW-15AT

Reviews:

Related manuals for CSW-15AT

Brands by name

Popular brands