CAMBRIDGE CSW-15AT Installation, Setup And Operation Instructions Download Page 3 | Manualshive

Page: 3 / 14

background image

3

METER CONNECTIONS

To connect power via AC wall adapter cable to the

CSW-15AT

meter. First make sure the

On/Off switch on the rear of the meter is in the off position. Connect the wall adapter to your
110VAC outlet. Next, connect the other end of the cable to the connector on the rear of the
indicator.

On/OFF
Switch

COMMUNICATIONS SIGNAL

PORT

Pin #  Description                                      Pin #  Description
  1 ------ Shield                                             1 ------ +EXC
  2 ------ RXD                                               2 ------ -SIG
  3 ------ TXD                                               5 ------ Shield
      4 ------ +5V                                                6 ------ -EXC
  5 ------ SGND                                            7 ------ +SIG

«
1
2
3
4
5
...
»

Summary of Contents for CSW-15AT















Reviews:

No comments

Related manuals for CSW-15AT

EZ Link DAL 150

Brand: Harman Kardon Pages: 16

Brand: Quadratec Pages: 8

Brand: QVS Pages: 1

Brand: Unimig Pages: 16

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: LANSING LIGHTING Pages: 4

Brand: Rola Pages: 3

THERMASGARD HFTM-Q

Brand: S+S Regeltechnik Pages: 16

Brand: Oben Pages: 12

Brand: VOLTCRAFT Pages: 84

Brand: BabySense Pages: 28

Brand: Scame electrical solutions Pages: 8

Brand: Easee Pages: 12

Brand: madbeanpedals Pages: 2

Brand: Vadsbo Pages: 2

Brand: Uniflame Pages: 2

Brand: Velleman Pages: 6

Brand: Zippy Tech. Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands