background image

 

PTP 820C Quick Start Guide 

 

Page 16 

Installing the Activation Key 

New PTP 820C units are delivered with a default activation key that enables you to manage and configure the unit. 
Additional feature and capacity support requires you to enter an activation key cipher in the Activation Key 
Configuration page. Contact your 
vendor to obtain your activation 
key cipher.  
If the activation-key-enabled 
capacity and feature set is 
exceeded, an Activation Key 
Violation alarm occurs and the 
Web EMS displays a yellow 
background and an activation 
key violation warning. After a 48-
hour grace period, all other 
alarms are hidden until the 
capacity and features in use are 
brought within the activation 
key’s capacity and feature set. 
Demo mode is available, which 
enables all features for 60 days. 
When demo mode expires, the 
most recent valid activation key goes into effect.  

To enter a new activation key, select Platform > Activation Key > Activation Key Configuration. The Activation Key 
Configuration page opens. 

 
 

Enter the activation 
key cipher here 
and click 

Apply

.

To activate Demo mode, 
select 

Enable 

here and 

click 

Apply

.

Displays the number of 
hours that remain before 
demo mode expires.

Summary of Contents for PTP 820C
























Reviews: