background image

 

2.

 

Before you begin

 

 

Introductory NOTES

 

This  operating  manual  includes  notations  and  symbols  that  make  it  easier  for  you  to  read  this 

document  and  which  are  intended  to  ensure  that  you  are  able  to  work  safely  with  Calyxo  solar 

modules.

 

 
 

 

SYMBOLS FOR SAFETY INSTRUCTIONS

 

 

Possible danger, injuries or damage 

Warning: dangerous electrical voltages 

Important information

 

2.1

 

Product features

 

 

PROPER 

U

SE

 

Calyxo solar modules are used to generate electrical power in photovoltaic systems. To generate power, 

the solar modules are attached to connectors and electrically connected to a control device such as an 

inverter or a charge controller.

 

 

Calyxo solar modules are developed and constructed in keeping with the latest technological 

developments. When used properly, in accordance with all of the instructions outlined in this operating 

manual and in combination with regular maintenance, they guarantee the highest level of safety.

 

 

The operator is responsible for full compliance with the instructions for mounting, transporting, wiring, 

storing, operating, cleaning and maintaining Calyxo solar modules outlined in this operating manual.

 

Any usage of Calyxo solar modules other than that described in this operating 

manual is prohibited. Calyxo shall assume no liability for damage to or caused by 

solar modules resulting from improper use.

 

Summary of Contents for CX1






























Reviews: