CALEFFI FPC-N34-1618 Instruction Sheet Download Page 6

Page: 6 / 20

Wiring diagrams: from devices (MODBUS-RTU) to Gateway (Ethernet)

See the diagrams below for the connection for the different devices (from MODBUS to BACnet network).

Device - Gateway connections

Gateway Pins

Devices

B +

A -

Legiomix_6000_Series

B (16)

A (18)

Legiomix_2_0_6000_Series

Conteca_Easy_750_Series

B (17)

A (18)

5. USE WEB CONFIGURATOR TO SETUP THE GATEWAY

Connect the PC to gateway via the Ethernet Port

Connect a CAT5 Ethernet cable (Straight through or Cross-Over) between the local PC and gateway.

NOTE: The Default IP Address of gateway is 192.168.1.24, subnet mask is 255.255.255.0. If the PC and gateway are on different

IP Networks, assign a static IP Address to the PC on the 192.168.1.1 network.

Device A

Device B

Device C

One or multiple

Ethernet Field Protocol

BACnet IP

One or multiple Serial Devices

RS485 Modbus-RTU

Device D

One or multiple

RS485 BACnet MS/TP

Device A

Device

Device C

One or multiple

Ethernet Field

Protocol

BACnet IP

One or multiple Serial Devices

RS485 Modbus-RTU

Device D

One or multiple

RS485 BACnet MS/TP

GATEWAY

Legiomix 2.0 6000 Series

RS-485 cable

Ethernet cable

Power

Legiomix 6000 Series

Conteca Easy 750 Series

ETHERNET
BACNET

RS485
MODBUS

Summary of Contents for FPC-N34-1618





















Search results

Summary of Contents for FPC-N34-1618

Reviews:

Related manuals for FPC-N34-1618

Brands by name

Popular brands

CALEFFI FPC-N34-1618, Instruction Sheet

Search results

Summary of Contents for FPC-N34-1618

Reviews:

Related manuals for FPC-N34-1618

Brands by name

Popular brands