CalAmp Sentry 4G-900 User Manual Download

Page: 46 / 48

SPECIFICATIONS

001-9193-001 Version 1

Page 46 of 48

Sentry 4G 900

User Manual

SPECIFICATIONS

Product specifications are subject to change without notice.

GENERAL SPECIFICATIONS

Interface Connectors:

Two 10/100 BaseT auto-MDIX, RJ-45

USB A Female Client port

3-wire serial in a USB mini B female form factor

Power Connector:

4-pin Weidmuller 1615550000

LED Indicators:

PWR, STAT, GPS, 4G, WiFi, ETH0, ETH1

Antenna Interface:

Two 4G Antennas: 50-Ohm TNC Female

GPS Antenna: 50-Ohm, 3.3V SMA Female

Two WiFi Antennas: 50-Ohm RP-SMA Plug

Size:

7 (L) x 7 (W) x 2.2(H) inches (17.8 x 17.8 x 5.6 cm)

Weight:

4 lbs (1.81 kg)

Power Input:

10-30 VDC

Current Drain:

(Average at 13.8 VDC)

TX Power Range:

4G: BTS controlled, up to 30 dBm (SIMO & SISO)

WiFi: 26 dBm (802.11b) & 21-26 dBm (802.11g)

Frequency Range:

4G: 902-928 MHz ISM Band

Channels:

5 to 7 non-overlapping 3.5 MHz channels (up to 20 overlapped)

Modulation:

S-OFDMA TDD QPSK, 16QAM, 64QAM

Diversity:

2x2 MIMO Matrix A

Operating Temperature:

-30°C to +60°C (-22 to +140 °F)

Vibration:

MIL-810F 514.5, SAE J1455 4.9

Shock:

MIL-810F 516.5, SAE J1455

Protocols:

Ethernet / IPV4 suite, DHCP client/server, NAT

Management:

HTTP embedded WEB server

Certifications:

FCC Part 15b, IC

Reserved for future use

Current Drain

With WiFi module

3.5 A

Without WiFi module

2.6 A

Summary of Contents for Sentry 4G-900

















































Search results

Summary of Contents for Sentry 4G-900

Reviews:

Related manuals for Sentry 4G-900

Brands by name

Popular brands

CalAmp Sentry 4G-900, User Manual

Search results

Summary of Contents for Sentry 4G-900

Reviews:

Related manuals for Sentry 4G-900

Brands by name

Popular brands