CalAmp Sentry 4G-900 User Manual Download

Page: 20 / 48

CONFIGURATION

001-9193-001 Version 1

Page 20 of 48

Sentry 4G 900

User Manual

5.2.1

Home Page Parameter Descriptions

System Information
Unit ID:

Sentry4G unit identification number (configured under General Settings).

System Up Time

: System Up Time displays a counter that starts when the unit is powered

on and resets when the unit is powered down or hardware reset.

Software Version:

This reflects the version of application software loaded on the unit.

WWAN

Interface Status

: indicates if the device has an established connection to the WWAN. Status

is UP or DOWN

IP Address

: WWAN IP address of the Sentry 4G unit.

Subnet Mask:

This subnet mask of the WWAN interface

MAC Address

: Media Access Control Address of the WWAAN interface.

ETH0 and ETH1
Interface Status

: indicates if the device has an established connection to the LAN on ETH0

or ETH1 interface. Status is UP or DOWN

IP Address:

IP address assigned to the ETH0/ETH1 interface

Subnet Mask:

The Subnet mask assigned to the ETH0/ETH1 interface

MAC Address:

Media Access Control Address of the ETH0/ETH1 interface

WLAN (Access Point or Client)
Interface Status:

Indicates if the WiFi interface is “UP” or “DOWN”

IP Address:

IP address assigned to the WiFi interface of this device. When the WiFi

interface is set to operate in WiFi Client mode, the WiFi Access Point must have a DHCP
server running to assign an IP address to its WiFi clients.

Subnet Mask:

Subnet Mask assigned to the WiFi interface of this device.

MAC Address:

Media Access Control Address of the WiFi interface.

5.3

WWAN Parameters

This page contains WWAN configuration information and settings.

5.3.1

Main

This screen contains main WWAN configuration. Select “Enabled” to enable WWAN interface and

“Disabled” to disable WWWAN interface. See Figure 9.

Summary of Contents for Sentry 4G-900

















































Search results

Summary of Contents for Sentry 4G-900

Reviews:

Related manuals for Sentry 4G-900

Brands by name

Popular brands

CalAmp Sentry 4G-900, User Manual

Search results

Summary of Contents for Sentry 4G-900

Reviews:

Related manuals for Sentry 4G-900

Brands by name

Popular brands