manualshive.com logo in svg

CAEL 4PG8000, Installation And Operation Manual, Page: 15 / 16

Share
Download
CAEL 4PG8000 Installation And Operation Manual Download Page 15

Capital Automotive Equipment

Model:4PG8000

1

Every six months check the nuts of all anchor bolts for correct installation torque Tinst.

2

Retighten them as required.

Installation Torque Tinst

4PG8000

80 Nm

7.4 Cleaning

Do not use high pressure / steam jet cleaners or caustic cleaning agents.

Risk of damage!

1

Periodically wash off aggressive substances and treat the lift with oil or wax spray.

2

Repair damage to the paintwork immediately to prevent corrosion. The RAL number is

available through the manufacturer.

Chapter 8 Trouble shooting

A list of possible troubles and solutions is given below:

TROUBLE

:

POSSIBLE CAUSE

:

SOLUTION

:

The lift does not work

The main switch is not turned on

Turn the switch on

There is no power

Check Power on to restore if
necessary

The electrical wires are disconnected

Reconnect

Fuses are blown

Check for correct voltage
Replace

The lift does not raise

The lift is overloaded

Check the vehicle weight

The motor direction of rotation is not
correct.

Interchange the two phases on
the main switch

The oil in the power unit is not sufficient.

Add some hydraulic oil

The UP button is faulty.

Check

UP

button

and

connection for proper operation.
Replace if needed

The maximum pressure valve clogged or
leaks

Check and clean if dirty

or

replace if faulty

The lowering valve does not close.

Check and clean, if dirty or
replace if faulty

Summary of Contents for 4PG8000

















Reviews:

No comments