Cadillac STS 2006 Repair Instructions Download Page 35 | Manualshive

Page: 35 / 51

background image

10/25/2014

Printer Friendly View

http://www2.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&className=

35/51

CAUTION: Compressed valve springs have

high tension against the valve spring
compressor. Valve springs that are not properly
compressed by or released from the valve spring
compressor can be ejected from the valve spring
compressor with intense force. Use care when
compressing or releasing the valve spring with
the valve spring compressor and when removing
or installing the valve stem keys. Failing to use
care may cause personal injury.

NOTE: Do not compress the valve springs

less than 24.0 mm (0.943 in). Contact between
the valve spring retainer and the valve stem oil
seal can cause potential valve stem oil seal
damage.

8. Tighten the EN 46110 valve spring compressor nut (2). See Special Tools .

«
...
33
34
35
36
37
...
»

Summary of Contents for STS 2006




















































Reviews:

No comments

Related manuals for STS 2006

Brand: AA Products Pages: 6

Brand: RaceChip Pages: 12

Brand: U & Me Brothers Pages: 6

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

Brand: Kia Pages: 51

Brand: Road Ranger Pages: 22

Brand: RBO Pages: 15

Brand: Kia Pages: 58

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Brand: Prime Design Pages: 12

Brand: Menabo Pages: 8

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brand: Navman Pages: 27

Brand: Hyundai Pages: 380

Brand: Harbor Freight Tools Pages: 8

Brand: Haltech Pages: 12

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands