Cadillac STS 2006 Repair Instructions Download Page 25 | Manualshive

Page: 25 / 51

background image

10/25/2014

Printer Friendly View

http://www2.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&className=

25/51

care may cause personal injury.

NOTE: Do not compress the valve springs

less than 24.0 mm (0.943 in). Contact between
the valve spring retainer and the valve stem oil
seal can cause potential valve stem oil seal
damage.

8. Tighten the EN 46110 valve spring compressor nut (2). See Special Tools .

9. Using the EN 46117 , remove the valve keepers. See Special Tools .

10. Loosen the EN 46110 valve spring compressor nut. See Special Tools .

11. Remove the valve spring retainer.

Fig 3: View Of Valve Spring Keepers

Courtesy of GENERAL MOTORS CORP.

«
...
23
24
25
26
27
...
»

Summary of Contents for STS 2006




















































Reviews:

No comments

Related manuals for STS 2006

Brand: Vauxhall Pages: 2

Brand: Dometic GROUP Pages: 20

Brand: Thule Pages: 8

Brand: Saab Pages: 445

Brand: AutoWatch Pages: 4

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

TRI-FOLD PG9300RF

Brand: Pet Gear Pages: 4

Brand: Buick Pages: 20

Brand: Volvo Pages: 42

Brand: GARO Pages: 15

Brand: rockymounts Pages: 6

PRIME DESIGN HRR3-E-PM42

Brand: Safe Fleet Pages: 12

Brand: N.R. AUTOSEATS Pages: 8

Brand: Lexus Pages: 830

Brand: iSimple Pages: 12

Brand: STO N SHO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands