Cadillac STS 2006 Repair Instructions Download Page 49

Page: 49 / 51

10/25/2014

Printer Friendly View

http://www2.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&className=

49/51

3. Carefully install the cylinder head with the exhaust manifold to the engine. Refer to Cylinder Head

Installation - Left Side .

4. Install the oil filter adapter upper bolt. Refer to Oil Filter Adapter Installation .

5. Install the oil level indicator. Refer to Oil Level Indicator and Tube Replacement .

6. Install the catalytic converter to the exhaust manifold. Refer to Catalytic Converter Replacement -

Left Side (LY7) .

7. Install the wiring harness bracket to the rear of the cylinder head.

8. Install the surge tank hose to the bracket at the rear of the cylinder head.

9. Install the power steering pump bolts. Refer to Power Steering Pump Installation .

10. Install the wiring harness connector bracket from the side of the cylinder head.

Fig 2: View Of Left Cylinder Head

Courtesy of GENERAL MOTORS CORP.

Summary of Contents for STS 2006




















































Search results

Summary of Contents for STS 2006

Reviews:

Related manuals for STS 2006

Brands by name

Popular brands

Cadillac STS 2006, Repair Instructions

Search results

Summary of Contents for STS 2006

Reviews:

Related manuals for STS 2006

Brands by name

Popular brands