BYOC Build Your Own Clone Phase Royal Kit Instructions Manual Download Page 2

 

Tech Support: 

BYOC, LLC makes no promises or guarantees that you will sucessfully complete your kit 
in a satisfactory mannor.  Nor does BYOC, LLC promise or guarantee that you will 
receive any technical support.  Purchasing a product from BYOC, LLC does not entitle 
you to any amount of technical support.  BYOC, LLC does not promise or guarantee that 
any technical support you may receive will be able to resolve any or all issues you may 
be experiencing. 
 
That being said, we will do our best to help you as much as we can.  Our philosophy at 
BYOC is that we will help you only as much as you are willing to help yourself.  We 
have a wonderful and friendly DIY discussion forum with an entire section devoted to the 
technical support and modifications of BYOC kits. 
 

www.buildyourownclone.com/board

 

 
When posting a tech support thread on the BYOC forum, please post it in the correct 
lounge, and please title your thread appropriately.  If everyone titles their threads 
“HELP!”, then it makes it impossible for the people who are helping you to keep track of 
your progress.  A very brief discription of your specific problem will do.  It will also 
make it easier to see if someone else is having or has had the same problem as you.  The 
question you are about to ask may already be answered.  Here are a list of things that you 
should include in the body of your tech support thread:  
1. A detailed explanation of what  the problem is. (not just,  “It doesn’t work, help”)  
2. Pic of the top side  of your  PCB.  
3. Pic of the underside of your PCB.  
4. Pic that clearly  shows your footswitch/jack wiring and the wires going to the PCB  
5. A pic  that clearly shows your wiring going from the PCB  to the pots and any other  
switches(only if your kit has non-PC mounted pots and switches) 
6. Is bypass working?  
7.  Does the LED come on?  
8. If you  answer yes to 6 and 7, what  does the pedal do when it is "on"?  
9. Battery or adapter.(if  battery, is it good? If adapter, what type?)  
 
Also, please only post pics that are in focus.  You're only wasting both parties' time if you 
post out of focus, low res pics from your cell phone. 

 
Revision Notes: 

Rev 1.0 There are no known errors. 
Rev 1.1: Replaced 2 ‘47n’ capacitors with electrolytic capacitors. 

See page 18 for an 

explanation

.  

 
 

Copyrights: 

All material in this document is copyrighted 2009 by BYOC, LLC 

Summary of Contents for Build Your Own Clone Phase Royal Kit


































Reviews: