manualshive.com logo in svg

Byan Systems HYD 1000, Installation And Technical Manual

Share
Download
Byan Systems HYD 1000 Installation And Technical Manual Download Page 28

BYAN SYSTEMS, INC. 

Automated Gate and Access Control Products 

 
 

413 Linden • Lusk, WY 82225 • (800) 223-2926 

 

25

 

G2M CONTROL BOARD 

 

 

 

Description: 

 
This 115V/220V single-phase electronic control unit is suitable for single-phase motors, and can 
drive up to two different motors.  There is a leaf delay incorporated with the use of the plug in 
car.  Nine dip-switches can select different options for the control unit. 
 
There are three possible timing potentiometers: opening time, automatic closing time, and the 
closing time.  A dip-switch can double the opening and closing time. 
 

Characteristics: 

 

Buttons 

 

Reversing Button: The first activation will make the gate operate.  The second activation will 
make the gate stop.  The third activation will reverse the gate direction while dip-switch 2 is on.  
With dip-switch 3 off, during the close cycle the gate will auto reverse to open. 
 
Opening Button: Used only to open and hold open the gate. 
 
Closing Button: Used only to close the gate. 
 
Stop Button:  (Normally closed contact) Stops the gate in opening/closing. 

Summary of Contents for HYD 1000





































Reviews:

No comments

Brands by name

Popular brands

Load more brands