BW Broadcast RBRX1 Preliminary Manual Download

Page: 20 / 23

RBRX1 Parameters

The 'SYSTEM' menu contains all the system controls (non processing) such as remote control and secu-
rity

'CODE LOCK'

This enables or disables the security code lock. The options are enabled and disabled. More

information is available in the code lock section of this manual.

The

'ETHERNET'

menu contains the controls relevant to the LAN/NET port.

'DHCP'

Turns on/off the DHCP client, allowing the unit to automatically obtain an IP address, default

gateway and subnet mask from a DHCP server.

'IP'

Sets the IP address of the LAN port.

'DG'

Sets the default gateway of the LAN port.

'PORT'

Sets the port number of the webserver.

'Screen saver'

This allows the time-out before the screensaver starts to be adjusted between 5 and 30 min-

utes.

'Clicker'

This allows the button click to be turned on/off.

Summary of Contents for RBRX1
























Search results

Summary of Contents for RBRX1

Reviews:

Related manuals for RBRX1

Brands by name

Popular brands

BW Broadcast RBRX1, Preliminary Manual

Search results

Summary of Contents for RBRX1

Reviews:

Related manuals for RBRX1

Brands by name

Popular brands