BW Broadcast RBRX1 Preliminary Manual Download Page 19

Page: 19 / 23

RBRX1 Parameters

'OUT2 Level'

controls the output level of the second BNC output. Range is 0dBu to +12dBu.

The 'SCHEDULE' menu contains all the controls for the dayparting (REAL TIME CLOCK) preset switch-
ing.

'TIME'

Sets the time and day of the RBRX1’s Real Time Clock.

'Sync to RDS ON/OFF:

Controls whether the RTC is syncronised with time information which arrives over

RDS.

'DAYPARTING ON/OFF:

Enables or disables the scheduling.

'DP(X) ON/OFF'

Enables or disables an individual daypart schedule.

'DP(X)'

Sets the preset to switch to when this daypart is triggered.

'DP(X) START'

Sets the start time day and time of the daypart. There is also an ‘ALL days’ option.

'DP(X) LENGTH'

Sets the length in minutes that the daypart will run for.

The 'ALARMS/TRIGGERS' menu contains all the controls that affect the alarm outputs, trigger inputs
and auto fallback.

The

'TRIGGER INPUTS'

menu contains the controls relevant to the trigger inputs.

The

'TRIGGER INPUT (X)'

menu contains all the controls relevant to the (X)th trigger input

'Action'

selects what action the input will trigger. Options are change preset and change source.

'Preset'

selects which preset to change to if action is set to change preset.

'Source'

selects which source to change to if action is set to change source. Options are Radio,

Digital In, Analog in, Mixer, Sine and Backup.

The

'OUTPUTS'

menu contains the controls relevant to the alarm outputs.

The

'OUTPUT (X)'

menu contains all the controls relevant to the (X)th alarm output.

'Source'

selects which detector is the source for the alarm. Options are signal, pilot, audio level,

USN, Multipath, PI, TA and TP.

'Delay'

selects how long the detector has to be in an error state before an alarm is trigger. This also

controls how long the detector has to be in a correct state before an alarm is de-activated.

'Pin Polarity'

selects whether the output is active high or active low

'Signal'

selects the threshold below which the signal will trigger an alarm.

'Pilot'

selects the threshold below which the pilot level will trigger an alarm.

'Audio Level'

selects the threshold below which the audio level will trigger an alarm.

'USN'

selects the threshold above which the USN detector will trigger an alarm.

'Multipath'

selects the threshold above which the USN detector will trigger an alarm.

'PI'

sets the PI code. If the PI code is different from the one set, an alarm will be triggered

'Action'

selects what action the input will trigger. Options are pin only, change preset and change

source.

'Preset'

selects which preset to change to if action is set to change preset.

'Source'

selects which source to change to if action is set to change source. Options are Radio,

Digital In, Analog in, Mixer, Sine and Backup.

Summary of Contents for RBRX1
























Search results

Summary of Contents for RBRX1

Reviews:

Related manuals for RBRX1

Brands by name

Popular brands

BW Broadcast RBRX1, Preliminary Manual

Search results

Summary of Contents for RBRX1

Reviews:

Related manuals for RBRX1

Brands by name

Popular brands