Bustec ProDAQ 3424 User Manual Download Page 32 | Manualshive

Page: 32 / 56

background image

3424-XX-UM

ProDAQ 3424 Function Card User Manual

Page 32 of 56

Copyright,



1998-2005 Bustec Production Ltd.

5.1. FCID

– Function Card ID Register

FCID register contains function card identification number. Readout should always give value of
3424H.

Bit

Access &

Default

Description

15:0

RO

0x3424

FCID

– Function Card ID

Function card identification number, 0x3424 for 8-channel, 24-bit Sigma-Delta ADC

5.2. FCVER

– Function Card Version Register

This is function card version register. Readout from this register gives information about PCB
revision and FPGA design revision.

Bit

Access &

Default

Description

15:8

RO

h

FPGA_REV

– FPGA Revision Number

FPGA design revision number, lower 4 bits define minor revision change and upper
4 bots define major revision change

7:0

RO

h

PCB_REV

– PCB Revision Number

PCB design revision number, lower 4 bits define minor revision change and upper 4
bits define major revision change

5.3. FCCRS

– Function Card Control and Status Register

This is control and status register of the function card.

Bit

Access &

Default

Description

15

R/W

0

MASTER

– Master

When the card is a Master, it generates all control signals, needed for the Data
Acquisition, internally. If the boards work in standalone configuration then all boards
have to be set to Master. If the boards are configured for the synchronous sampling
then only one board can be switched to be Master.

0 : the board is a Slave
1 : the board is a Master

USAGE



Can be changed only in IDLE_ST

14

Reserved

13

RO

h

DA_END

– Data Acquisition End

The bit is set by hardware after the normal end of Data Acquisition or when the
DA_SKIP has been performed. It is not set if Data Acquisition ends with the error.
This bit is cleared on arming command or clearing command.

1 : DA ended

USAGE



This bit can be used to detect the end of the Data Acquisition. There are

possible two ways: polling the bit or waiting for interrupt generated by this bit
when either Output Trigger or Direct Interrupt was enabled. The Data
Acquisition stop condition depends on the card configuration.



This bit is not set if Data Acquisition is ended by error or software reset

12:10

RO

h

MAINSM_ST

– Main State Machine States

The bits indicate the states of the main state machine.

000 : IDLE_ST
001 : DDSUD_ST

«
...
30
31
32
33
34
...
»

Summary of Contents for ProDAQ 3424

























































Reviews:

No comments

Related manuals for ProDAQ 3424

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

Brand: Eaton Pages: 8

Brand: Paradox Pages: 2

Brand: Paradox Pages: 44

TEMP2000 Series

Brand: Samwontech Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands