Page 6
User instructions
CD/MP3 operation
Playback
1:
Make sure you are in
CD
or
USB
mode, if not read the
‘Switching modes’
section above .
2:
Press the lid release button
(17)
on top of the unit .
When the lid opens insert a disc
(label side facing
upwards)
and close the lid until you hear a click . Or
follow
‘Loading a USB device’
for
USB MP3
playback .
3:
When the door is closed “
LOAD”
will appear on the
display as the unit detects compatible audio tracks .
3:
Playback will begin automatically from Track
01
.
4:
To stop playback press the
STOP
button
(2
,
33)
.
5:
To pause playback press the
PLAY/PAUSE
button
(10
,
30)
during playback . To resume playback press
once more .
Skipping Tracks
1:
To skip to the next track on a disc press
(5
,
21)
.
2:
To skip to the previous track press
(4
,
23)
.
Fast Searching Tracks
1:
To fast forward a track during playback press
FWD
(31)
on the remote control . Each press of the button
increases the search speed
EG:
2
x,
4
x &
6
x the next
press will resume normal playback . To fast rewind a
track during playback press the
REV (22)
button .
Repeat Operation
1:
During playback pressing the
REPEAT
button
(20)
will
flag the current track to repeat indefinitely . You will
see
flash on the display .
2:
Pressing the
REPEAT
button again will repeat all
tracks on the disc . You will see the
icon stop
flashing and remain solid .
3:
To cancel the repeat function press the
REPEAT
button for a third time . You will see the
icon
disappear from the display .
Numeric buttons
While listening to a CD or MP3 tracks a specific track
number can be played by pressing the relative digit
on the number buttons. EG track 6 would be 6. To play
track 12 you would press the 10+ button then 2.
Programme playback
Should you wish to create a playlist from a CD or MP3
tracks. Follow the below steps to program the playlist.
1:
Ensure any loaded disc is in
STOP
mode . Press the
PROG
button
(32)
to enter the programme setup
function .
2:
You will see
P01
appear on the display to indicate
program track
01
.
3:
Use the
/
buttons
(4/5
,
23/21)
to skip
between the track numbers . or use the numeric
buttons to enter the track number directly .
4:
When you have selected the track you wish to
program press the
PROG
button
(32)
again .
5:
The program track no will change to
P02
, and you can
continue programming following steps
3
-
4
each time .
6:
When you have programmed your playlist press the
PLAY/PAUSE
button
(10
,
30)
to begin playback .
7:
To cancel the programmed playlist press the
STOP
button
(2
,
33)
.
Random CD Operation
1:
Press the
RANDOM
button
(34)
on the remote control .
You will see
‘RAN’
appear on the display and the
CD
contents will be played once in a random order .
2:
To cancel the random operation press the
RANDOM
button again . You will see
‘RAN’
disapear from the
display .
FM (Radio) operation
Scanning for stations
1:
You can skip up or down the frequency range
manually by pressing the
REV (22)
or
FWD (31)
buttons on the remote or
(4)
or
(5)
buttons on
the unit to increase or decrease the frequency in
0
.
05
MHz
increments .
2:
Alternatively you can press the
SEARCH
button
(19)
.
This will scan the entire frequency range and store
any strong stations located into the preset memory
list .
NOTE: Pressing the SEARCH button again erases
any previously stored stations on the preset list.
