Bush Hog 14810RR1, Operator'S Manual

Page: 6 / 208

DEALER to CUSTOMER Pre-Delivery/ Operation Instructions
Dealer should inform the Purchaser of this product of Warranty terms, provisions, and procedures that are applica-
ble.Dealer should inform Purchaser to review the contents of the Operator’s Manual including safety equipment,
safe operation, and maintenance, to review the Safety Signs on the implement (and tractor if possible),and of Pur-
chaser’s responsibility to train his/her operators’s in safe operation procedures.
IMPLEMENTS: I have explained that Deflectors, Chain Guards, or Solid Skirts must be installed and maintained in-
good repair.
• DRIVELINES: I have made certain that all driveline, gearbox, and other shields are in good repair
and fastened securely in place to prevent injuries from entanglement or thrown objects.
• HYDRAULIC MACHINES: I have explained the necessity of using clean hydraulic oil, changing filters
as instructed, stopping leaks, damage caused by operating with over-heated oil, caring for hoses,
using hoses of proper rating, maintaining the specified operating pressure and the potential hazard
of oil’s penetrating the skin.
• FOLDING-TYPE IMPLEMENTS: I have explained that it is not possible to guard against thrown ob-
jects when the head is lifted off ground and that operator is responsible to watch out for persons in
the area. I have explained that the lifted mower head or boom can contact overhead obstructions with
damage to cables and telephone lines and possible injury. I have explained that the extended head
or boom or retracted boom cancontact power lines with resulting electrocution, injury or death and
that operator is responsible for keeping clear of such hazards.
PRE-DELIVERY SERVICE
CHECK AND ADJUST OR LUBRICATE AS REQUIRED
See Operator’s Manual for Details
Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete
MOWER TO TRACTOR CONNECTIONS
□
Draw Bar Length (Check And Set)
□
A-Frame Pivot & Links�Control Rods (Adjusted Equal)
□
Axle Height (Adjusted)
□
Cutting Height (Adjust)
□
Mount Kit-Pre-Operation Check Complete
□
Mower Wing (Adjust Level With The Center)
□
Mower Wing (Check For Proper Raising Operation)
□
C.V. Driveline (Check Max Turn Radius)
□
Pull Type Hitch (Height Adjustment)
□
Mounting Hardware Properly Torqued
SAFETY ITEMS
□
Protective Shields (Operation And Installation)
□
Driveline Clutch (Torque Limiter) (Adjust And Run In)
□
Safety Decals (Installed)
□
Operator’s Manual (Supplied)
□
Tractor PTO Shield (Installed)
□
S.M.V. Emblem (Installed If Needed)
□
Tongue Jack (Installation and Operation)
□
Safety Tow Chain (Installed)
□
ADMA Driveline Safety Manual Supplied
□
AEM Mower Safety Manual (Supplied in Canister)
□
AEM Mower Safety Video has been shown to Purchaser
LUBRICATION & HYDRAULICS
□
Gearbox (Oil Levels)
□
Hydraulic Oil Level (External Tank)
□
Tractor Hydraulic Oil Level
□
Hydraulic Hoses (Not Kinked Tighten Connections)
□
Front Pump Drive (Assembly Is Tight And Shaft
Properly Aligned)
MOWER
□
Spindle And Motor Bolts Properly Torqued
□
Spindle Oil Level
□
Blade Carrier Bolts Properly Torqued/Retaining Pin
In Place
□
Mower Cutting Height And Level Adjusted
□
Cutting Shaft Bearings Lubricated
□
All Hardware Properly Torqued
□
Tire and Air Pressure/Lug Nuts (Correct Torque)
□
Wheel Bearings (Check, Grease, and Preload)
ATTACHMENTS & INSTALLATION
□
Deflectors Front And Rear
□
Shredding Attachments
□
Correct Blade Rotation Direction
□
Axle Arms And Beams
□
Tongue And Control Rods (Installed And Adjusted)
□
All Bolts - Pins And Nuts (Proper Torque)