background image

Page 7

For technical questions, please call 1-888-866-5797.

Item 64734 
        

SENS (Sensitivity)

The SENS Adjusting Knob sets the level of 
sensitivity of the Motion Detector Head.
The Motion Detector Head is most sensitive 
to movement across the detection zone, 
rather than movement toward or away 
from the Motion Detector Head.
Turn the SENS dial anywhere between 
the minimum and maximum settings to 
adjust the level of sensitivity needed.

Note:

  Sensitivity is affected by the ambient 

air temperature.  If it is hot outside, the sensor 
may have difficulty detecting changes in 
heat.  In cold temperatures, the sensitivity is 
increased and may need to be adjusted.

Minimum Position 

Turn the dial counterclockwise 
to the minimum setting (-).  
Ideal for hot summer 
conditions or when nuisance 
tripping is a problem.  If the 
light is activated by small 
animals or rapid changes in 
heat, reduce sensitivity by 
turning the knob counterclockwise towards the 
minimum setting.

Maximum Position 

Turn the dial clockwise to the 
maximum setting (+).  Ideal for 
cold winter conditions or to 
maximize range.

TIME (Light Duration)

The TIME Adjusting Knob sets how long 
the Lamp will stay illuminated after motion 
is no longer detected by the sensor.

Minimum Position 

Turn the dial counterclockwise to 
the minimum for the Lamp stay 
illuminated for 10 seconds after 
motion is no longer detected.

Mid Range 

Adjust the dial between the 
Minimum and Maximum, to 
choose any time between 10 
and 100 seconds, for the Lamp 
to stay illuminated after motion 
is no longer detected.

Maximum Position 

Turn the dial clockwise to the 
maximum for the Lamp to stay 
illuminated for 110 seconds after 
motion is no longer detected. 

LUX (Light Level)

The LUX Adjusting Knob tells the sensor 
the level of darkness that must be reached 
before the Lamp illuminates.

Minimum Position

 

Turning the dial 
counterclockwise to the 
minimum setting lowers the 
sensor level.  The sensor will 
only trigger the Lamp to 
illuminate at dusk or when it is 
dark out.  This is the ideal 
position for general evening and night operation.

Maximum Position 

Turning the dial clockwise to 
the maximum setting increases 
the sensor level.  The Lamp will 
illuminate in most situations 
ranging from dark to daylight.

Note:

  If the Security Light is not operating at night due to interference from a street light or other 

interference, turn the LUX knob towards the maximum setting    .  Adjust the dial as needed 
between the minimum and maximum settings to achieve the desired level of sensitivity.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Summary of Contents for LED-SOLAR













Reviews: