background image

Page 3

For technical questions, please call 1-800-444-3353.

Item 69643 

        

7. 

Dress properly.

 Protective, electrically non-

conductive clothes and nonskid footwear are 

recommended when working with the Solar 

Powered Security Light. Wear restrictive 

hair covering to contain long hair.

8. 

use eye protection.

 Wear ANSI-approved impact 

safety goggles when setting up this product.

9. 

maintain products with care.

 Keep the Solar 

Powered Security Light clean for better and safer 

performance. Inspect the Light periodically. If 

damaged, have it repaired by a qualified technician.

10. 

Do not overreach.

 Keep proper footing and 

balance at all times. If a ladder is to be used during 

installation, it should be supported by an assistant.

11. 

Do not set up the Solar powered Security light 

if under the influence of alcohol or drugs.

 Read 

warning labels on prescriptions to determine if your 

judgement or reflexes are impaired while taking 

drugs. If there is any doubt, do not set up the Light.

12. 

niCd BatteRY muSt Be ReCYCleD 

OR DiSpOSeD OF pROpeRlY.  Do not 

short, incinerate or open battery.

13. 

have your power tool serviced by a 

qualified repair person using only identical 

replacement parts.

 

This will ensure that the 

safety of the power tool is maintained.

14. WARNING: Handling the cord on this product’s 

Charger will expose you to lead, a chemical 

known to the State of California to cause cancer, 

and birth defects or other reproductive harm. 

Wash hands after handling.   

(California Health & Safety Code § 25249.5, 

et seq.

)

15. The warnings, precautions, and instructions 

discussed in this instruction manual cannot 

cover all possible conditions and situations 

that may occur.  It must be understood by the 

operator that common sense and caution are 

factors which cannot be built into this product, 

but must be supplied by the operator.

 Save theSe inStRuCtiOnS.

Sa

Fet

Y

Ope

R

ati

O

n

m

aintenan

C

e

Setup

Summary of Contents for 69643













Reviews: