9
LED Status Indicator
The LED (red light) provides valuable information about the system and is also a theft deterrent.
LED Status
LED Display
Armed
Flashing Slow
Disarmed
Off
Passive Arming
Flashing Fast (arming count down)
Valet
Constantly On
Violated Zone
Triggered Device
# of Flashes
Zone 2
On Board Shock Sensor
2 Flashes
Zone 3
External Sensors
3 Flashes
Zone 4
Voltage Sensor
4 Flashes
Zone 5
Door Switches
5 Flashes
Zone 6
Ignition
6 Flashes
Plug In Override Switch
In the event your remote control is lost, damaged or malfunctions; this switch allows you to disarm your system.
You must first open the door to the vehicle, turn ignition to the "ON" position, then press the override
switch. The siren will silence and you will now be able to start the engine. NOTE: A door must remain open
during this procedure.
Automatic Passive Arming
To program Automatic Passive Arming On, disarm the system, press and hold Button #3 for 10 seconds, until the unit
chirps once. Release Button #3 then press and release Button #3 again within (2) two seconds. The system will chirp
once again to indicate that Passive Arming is now programmed ON. NOTE: Factory setting is Automatic Passive Arming
Off.
Automatic Passive Arming with Door Locks On
To program Automatic Passive Arming with Door Locks On, disarm the system, press and hold Button #3 for 10 seconds,
until the unit chirps once. Release Button #3 then press and release Button #3 again within (2) two seconds. The
system will chirp once. Press and release Button #3 again and the unit will chirp twice. The Automatic Passive
Arming with Door Locks is now programmed.
Passive Arming Off
To program Passive Arming Off, disarm the system. Press and hold Button #3 for 10 seconds, until the unit chirps
once. Press and release Button #3, the unit will chirp three times. Passive Arming is programmed Off.
High Theft
To program High Theft On, press Button #2 within two seconds after arming the unit, the system will chirp once (or
flash the parking lights once if Silent Arming is activated). The High Theft feature will only function for this
arming only, after the unit is disarmed it reverts back to High Theft Off.
Shock Sensitivity Reduction
To reduce the on-board shock sensitivity to 50% (for this arming only), press Button #1 again within two seconds
after arming. The system will chirp once (or flash the parking lights once if Silent Arming is activated). To shut
off the Current Sensor (for this arming only) press Button #1 a second time after arming, the unit will chirp once.
The Current Sensor is programmed Off.
Valet Mode On
To activate Valet Mode, disarm the system. Press and hold Button #4 until the system chirps once, release Button
#4. Press and release Button #4 again within two seconds and the system will chirp once again. The LED will remain
on (constant) when in Valet Mode. NOTE: Factory setting is Valet Mode Off.
Valet Mode Off
To deactivate Valet Mode, disarm the system. Press and hold Button #4 until the system chirps once, release Button
#4. Press and release Button #4 again within two seconds and the system will chirp twice. The LED will remain off.
The unit is now out of Valet Mode. NOTE: Factory setting is Valet Mode Off.
NOTE: Valet Mode can also be programmed On and Off through the Override Switch. With the ignition key in the On
position, press and hold the Override Switch for (2) two seconds or until the unit chirps once. The LED will remain
On (constant) while in Valet Mode. Turn off Valet Mode from the Override Switch and turn your ignition key to the
On position. Press and hold the Override Switch for (2) two seconds or until the unit chirps twice. The Valet Mode
is programmed Off and the LED will turn off.
Current Sensor On
Disarm the system and press Button #4 for (10) ten seconds or until the unit chirps once. Release Button #4 and
press Button #3 within (2) two seconds. The unit will chirp once indicating that Current Sensing is programmed On.
NOTE: Factory setting is Current Sensing Off.
Current Sensor Off
Disarm the system and press Button #4 for (10) ten seconds or until the unit chirps once. Release Button #4 and
press Button #3 within (2) two seconds. The unit will chirp twice indicating that Current Sensing is programmed
Off.
OPERATING INSTRUCTIONS
